1
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
,Automotive Steering, Suspension, & Alignment, 8e (Halderman) cn cn cn cn cn cn cn
Appendix 1 cn
1) A customer complains that the steering lacks power assist all the time. Technician A says that
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
the power steering pump drive belt could be slipping or loose. Technician B says that worn outer t
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
ie rod ends could be the cause. Which technician is correct?
cn cn cn cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: A c n
2) A front-wheel-
cn
drive vehicle pulls toward the right during hard acceleration. The most likely cause is .
cn cn cn cn cn cn cn cn cn cn cn cn cn cn
A) worn or defective tires cn cn cn
B) leaking or defective shock absorbers cn cn cn cn
C) normal torque steer cn cn
D) a defective power steering rack-and-
cn cn cn cn
pinion steering assembly Answer: C
cn cn cn c n
3) When replacing a rubber-bonded socket (RBS) tie rod end, the technician should be sure to
cn cn cn cn cn cn cn cn cn cn cn cn cn cn
.
A) remove the original using a special tool cn cn cn cn cn cn
B) install and tighten the replacement with the front wheels in the straight-ahead position
cn cn cn cn cn cn cn cn cn cn cn cn
C) grease the joint before installing on the vehicle
cn cn cn cn cn cn cn
D) install the replacement using a special clamp vise
cn cn cn cn cn cn cn cn
Answer: B c n
4) Whenever installing a tire on a rim, do not exceed cn cn cn cn cn cn cn cn cn cn .
A) 25 PSI cn
B) 30 PSI cn
C) 35 PSI cn
D) 40 PSI cn
Answer: D c n
5) Two technicians are discussing mounting a tire on a wheel. Technician A says that for best ba
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
lance, the tire should be match mounted. Technician B says that silicone spray should be used to l
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
ubricate the tire bend. Which technician is correct?
cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: A c n
2
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
,6) Technician A says that radial tires should only be rotated front to rear, never side to side.
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
Technician B says that vehicle manufacturers usually recommend that radial tires should be r
cn cn cn cn cn cn cn cn cn cn cn cn cn
otated using the modified X method. Which technician is correct?
cn cn cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: B c n
7) For a tire that has excessive radial runout, Technician A says that it should be broken down on
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
a tire-
cn
changing machine and then rotated 180 degrees on the wheel and retested. Technician B says tha
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
t the tire should be replaced. Which technician is correct?
cn cn cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: A c n
8) Technician A says that overloading a vehicle can cause damage to the wheel bearings. Techni
cn cn cn cn cn cn cn cn cn cn cn cn cn cn
cian B says that tapered roller bearings used on a nondrive wheel should be adjusted hand tight on
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
ly after seating. Which technician is correct?
cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: C c n
9) Defective wheel bearings usually sound like cn cn cn cn cn cn .
A) a growl cn
B) a rumble cn
C) snow tires cn
D) All of the above cn cn cn cn
Answer: D c n
10) Defective outer CV joints usually make a clicking noise cn cn cn cn cn cn cn cn cn
A) only when backing cn cn
B) while turning and moving cn cn cn
C) while turning only cn cn
D) during braking cn c
Answer: B
n c n
11) The proper lubricant usually specified for use in a differential is
cn cn cn cn cn cn cn cn cn cn cn .
A) SAE 15-40 engine oil cn cn cn
B) SAE 80W-90 GL-5 cn cn
C) STF
D) SAE 80W-140 GL-1 cn cn
3
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
, Answer: B
c n
4
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
,Automotive Steering, Suspension, & Alignment, 8e (Halderman) cn cn cn cn cn cn cn
Appendix 1 cn
1) A customer complains that the steering lacks power assist all the time. Technician A says that
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
the power steering pump drive belt could be slipping or loose. Technician B says that worn outer t
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
ie rod ends could be the cause. Which technician is correct?
cn cn cn cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: A c n
2) A front-wheel-
cn
drive vehicle pulls toward the right during hard acceleration. The most likely cause is .
cn cn cn cn cn cn cn cn cn cn cn cn cn cn
A) worn or defective tires cn cn cn
B) leaking or defective shock absorbers cn cn cn cn
C) normal torque steer cn cn
D) a defective power steering rack-and-
cn cn cn cn
pinion steering assembly Answer: C
cn cn cn c n
3) When replacing a rubber-bonded socket (RBS) tie rod end, the technician should be sure to
cn cn cn cn cn cn cn cn cn cn cn cn cn cn
.
A) remove the original using a special tool cn cn cn cn cn cn
B) install and tighten the replacement with the front wheels in the straight-ahead position
cn cn cn cn cn cn cn cn cn cn cn cn
C) grease the joint before installing on the vehicle
cn cn cn cn cn cn cn
D) install the replacement using a special clamp vise
cn cn cn cn cn cn cn cn
Answer: B c n
4) Whenever installing a tire on a rim, do not exceed cn cn cn cn cn cn cn cn cn cn .
A) 25 PSI cn
B) 30 PSI cn
C) 35 PSI cn
D) 40 PSI cn
Answer: D c n
5) Two technicians are discussing mounting a tire on a wheel. Technician A says that for best ba
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
lance, the tire should be match mounted. Technician B says that silicone spray should be used to l
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
ubricate the tire bend. Which technician is correct?
cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: A c n
2
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
,6) Technician A says that radial tires should only be rotated front to rear, never side to side.
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
Technician B says that vehicle manufacturers usually recommend that radial tires should be r
cn cn cn cn cn cn cn cn cn cn cn cn cn
otated using the modified X method. Which technician is correct?
cn cn cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: B c n
7) For a tire that has excessive radial runout, Technician A says that it should be broken down on
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
a tire-
cn
changing machine and then rotated 180 degrees on the wheel and retested. Technician B says tha
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
t the tire should be replaced. Which technician is correct?
cn cn cn cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: A c n
8) Technician A says that overloading a vehicle can cause damage to the wheel bearings. Techni
cn cn cn cn cn cn cn cn cn cn cn cn cn cn
cian B says that tapered roller bearings used on a nondrive wheel should be adjusted hand tight on
cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn cn
ly after seating. Which technician is correct?
cn cn cn cn cn cn
A) Technician A only cn cn
B) Technician B only cn cn
C) Both Technicians A and B cn cn cn cn
D) Neither Technician A nor B cn cn cn cn cn
Answer: C c n
9) Defective wheel bearings usually sound like cn cn cn cn cn cn .
A) a growl cn
B) a rumble cn
C) snow tires cn
D) All of the above cn cn cn cn
Answer: D c n
10) Defective outer CV joints usually make a clicking noise cn cn cn cn cn cn cn cn cn
A) only when backing cn cn
B) while turning and moving cn cn cn
C) while turning only cn cn
D) during braking cn c
Answer: B
n c n
11) The proper lubricant usually specified for use in a differential is
cn cn cn cn cn cn cn cn cn cn cn .
A) SAE 15-40 engine oil cn cn cn
B) SAE 80W-90 GL-5 cn cn
C) STF
D) SAE 80W-140 GL-1 cn cn
3
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
, Answer: B
c n
4
Copyright © 2021 Pearson Education, Inc.
cn cn cn cn cn
VERIFIEDBRAINBOOSTER
