ACI Shotcrete Nozzleman Certification
Practice Exam Questions And Correct
Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant
Download Pdf
1. The primary responsibility of a shotcrete nozzleman is to:
A. Mix shotcrete materials
B. Test compressive strength
C. Properly place and consolidate shotcrete at the work surface
D. Design shotcrete mixes
The nozzleman controls placement, consolidation, and final quality of
shotcrete by proper nozzle handling.
2. Which process uses compressed air to convey dry materials with water
added at the nozzle?
A. Wet-mix shotcrete
B. Pumped concrete
, C. Dry-mix shotcrete
D. Preplaced aggregate
Dry-mix shotcrete introduces water at the nozzle, allowing
adjustment during placement.
3. In wet-mix shotcrete, water is added:
A. At the nozzle
B. At the air compressor
C. Before pumping, at the mixer
D. After placement
Wet-mix shotcrete contains all ingredients, including water, mixed
before pumping.
4. Proper nozzle angle for most shotcrete applications is:
A. 30 degrees
B. 45 degrees
C. Approximately perpendicular (90 degrees) to the surface
D. Parallel to the surface
A near-perpendicular angle ensures good compaction and reduces
rebound.
5. Rebound in shotcrete refers to:
A. Hardened concrete falling off
B. Material that ricochets off the surface during placement
C. Excess water dripping
D. Over-spraying
, Rebound consists of aggregate and cement that do not adhere to the
surface.
6. Excessive rebound is most commonly caused by:
A. Low air pressure
B. Improper nozzle angle or distance
C. High cement content
D. Warm weather
Incorrect nozzle positioning prevents proper consolidation and
adhesion.
7. Which material should never be reused in shotcrete?
A. Fresh mix
B. Overspray
C. Rebound material
D. Cement
Rebound has altered proportions and reduced cement content,
leading to weak shotcrete.
8. Typical nozzle distance from the receiving surface is:
A. 6–12 inches
B. 2–4 feet
C. 6–8 feet
D. Over 10 feet
This distance allows proper velocity and compaction without
excessive rebound.
Practice Exam Questions And Correct
Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant
Download Pdf
1. The primary responsibility of a shotcrete nozzleman is to:
A. Mix shotcrete materials
B. Test compressive strength
C. Properly place and consolidate shotcrete at the work surface
D. Design shotcrete mixes
The nozzleman controls placement, consolidation, and final quality of
shotcrete by proper nozzle handling.
2. Which process uses compressed air to convey dry materials with water
added at the nozzle?
A. Wet-mix shotcrete
B. Pumped concrete
, C. Dry-mix shotcrete
D. Preplaced aggregate
Dry-mix shotcrete introduces water at the nozzle, allowing
adjustment during placement.
3. In wet-mix shotcrete, water is added:
A. At the nozzle
B. At the air compressor
C. Before pumping, at the mixer
D. After placement
Wet-mix shotcrete contains all ingredients, including water, mixed
before pumping.
4. Proper nozzle angle for most shotcrete applications is:
A. 30 degrees
B. 45 degrees
C. Approximately perpendicular (90 degrees) to the surface
D. Parallel to the surface
A near-perpendicular angle ensures good compaction and reduces
rebound.
5. Rebound in shotcrete refers to:
A. Hardened concrete falling off
B. Material that ricochets off the surface during placement
C. Excess water dripping
D. Over-spraying
, Rebound consists of aggregate and cement that do not adhere to the
surface.
6. Excessive rebound is most commonly caused by:
A. Low air pressure
B. Improper nozzle angle or distance
C. High cement content
D. Warm weather
Incorrect nozzle positioning prevents proper consolidation and
adhesion.
7. Which material should never be reused in shotcrete?
A. Fresh mix
B. Overspray
C. Rebound material
D. Cement
Rebound has altered proportions and reduced cement content,
leading to weak shotcrete.
8. Typical nozzle distance from the receiving surface is:
A. 6–12 inches
B. 2–4 feet
C. 6–8 feet
D. Over 10 feet
This distance allows proper velocity and compaction without
excessive rebound.
