Alberta Boiler Inspector Advanced Certification
Exam (Absa) Practice Exam Questions And
Correct Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant Download Pdf
1. Under the Safety Codes Act, the primary responsibility of an ABSA
boiler inspector is to
A. Approve design calculations for all pressure vessels
B. Enforce manufacturer warranty requirements
C. Verify compliance with applicable codes and regulations
D. Operate boilers during commissioning
Answer: C
Rationale: ABSA inspectors enforce compliance with codes,
standards, and Alberta legislation, not operation or warranties.
2. The governing code most commonly applied to power boilers in
Alberta is
A. CSA B51
B. ASME Section I
C. ASME Section VIII
D. NBIC Part 4
Answer: B
Rationale: ASME Section I applies to power boilers, while Section
VIII covers pressure vessels.
3. A boiler operating above 15 psi steam pressure is classified as a
A. Heating boiler
, B. Hot water boiler
C. Power boiler
D. Low-pressure vessel
Answer: C
Rationale: Steam boilers above 15 psi are defined as power
boilers.
4. The maximum allowable working pressure (MAWP) is determined
by
A. Operating temperature only
B. Lowest rated component
C. Safety valve capacity
D. Owner preference
Answer: B
Rationale: MAWP is limited by the weakest pressure-retaining
component.
5. When reviewing a manufacturer’s data report, the inspector must
verify
A. Welding cost details
B. Operator training records
C. Code stamping and certification
D. Fuel efficiency ratings
Answer: C
Rationale: Proper stamping and certification confirm code
compliance.
6. A safety valve must be set to relieve at or below
A. 90% of MAWP
B. 95% of MAWP
, C. 100% of MAWP
D. 110% of MAWP
Answer: C
Rationale: Safety valves are set at or below the MAWP.
7. The purpose of hydrostatic testing is to
A. Verify operational efficiency
B. Detect leaks and structural weakness
C. Measure heat transfer rates
D. Calibrate safety valves
Answer: B
Rationale: Hydrostatic testing confirms pressure integrity.
8. During an internal inspection, the inspector should primarily look
for
A. Paint condition
B. Scale, corrosion, and cracking
C. Nameplate cleanliness
D. Burner flame color
Answer: B
Rationale: Internal degradation directly affects pressure integrity.
9. The National Board Inspection Code (NBIC) is mainly used for
A. New construction only
B. Repairs and alterations
C. Operator certification
D. Fuel system design
Answer: B
Rationale: NBIC governs repairs and alterations of pressure
equipment.
Exam (Absa) Practice Exam Questions And
Correct Answers (Verified Answers) Plus
Rationales 2026 Q&A | Instant Download Pdf
1. Under the Safety Codes Act, the primary responsibility of an ABSA
boiler inspector is to
A. Approve design calculations for all pressure vessels
B. Enforce manufacturer warranty requirements
C. Verify compliance with applicable codes and regulations
D. Operate boilers during commissioning
Answer: C
Rationale: ABSA inspectors enforce compliance with codes,
standards, and Alberta legislation, not operation or warranties.
2. The governing code most commonly applied to power boilers in
Alberta is
A. CSA B51
B. ASME Section I
C. ASME Section VIII
D. NBIC Part 4
Answer: B
Rationale: ASME Section I applies to power boilers, while Section
VIII covers pressure vessels.
3. A boiler operating above 15 psi steam pressure is classified as a
A. Heating boiler
, B. Hot water boiler
C. Power boiler
D. Low-pressure vessel
Answer: C
Rationale: Steam boilers above 15 psi are defined as power
boilers.
4. The maximum allowable working pressure (MAWP) is determined
by
A. Operating temperature only
B. Lowest rated component
C. Safety valve capacity
D. Owner preference
Answer: B
Rationale: MAWP is limited by the weakest pressure-retaining
component.
5. When reviewing a manufacturer’s data report, the inspector must
verify
A. Welding cost details
B. Operator training records
C. Code stamping and certification
D. Fuel efficiency ratings
Answer: C
Rationale: Proper stamping and certification confirm code
compliance.
6. A safety valve must be set to relieve at or below
A. 90% of MAWP
B. 95% of MAWP
, C. 100% of MAWP
D. 110% of MAWP
Answer: C
Rationale: Safety valves are set at or below the MAWP.
7. The purpose of hydrostatic testing is to
A. Verify operational efficiency
B. Detect leaks and structural weakness
C. Measure heat transfer rates
D. Calibrate safety valves
Answer: B
Rationale: Hydrostatic testing confirms pressure integrity.
8. During an internal inspection, the inspector should primarily look
for
A. Paint condition
B. Scale, corrosion, and cracking
C. Nameplate cleanliness
D. Burner flame color
Answer: B
Rationale: Internal degradation directly affects pressure integrity.
9. The National Board Inspection Code (NBIC) is mainly used for
A. New construction only
B. Repairs and alterations
C. Operator certification
D. Fuel system design
Answer: B
Rationale: NBIC governs repairs and alterations of pressure
equipment.
