NYC Supervisor Carpenter (CUNY) Exam
Practice Questions And Correct Answers
(Verified Answers) Plus Rationales 2026
Q&A | Instant Download Pdf
1. Which tool is best used to check if a door frame is perfectly vertical?
A. Tape measure
B. Chalk line
C. Level
D. Framing square
Rationale: A level is specifically designed to determine plumb
(vertical) and level (horizontal) alignment.
2. What type of wood joint is most commonly used for framing walls?
A. Dovetail joint
B. Butt joint
C. Mortise and tenon
D. Lap joint
Rationale: Butt joints are simple and efficient, making them standard
for wall framing.
,3. In supervising carpentry work, which document outlines scope,
materials, and workmanship standards?
A. Time sheet
B. Safety log
C. Construction specifications
D. Inventory list
Rationale: Specifications define required materials, methods, and
quality standards.
4. Which nail is most appropriate for exterior decking?
A. Common steel nail
B. Galvanized nail
C. Finish nail
D. Brad nail
Rationale: Galvanized nails resist corrosion, making them suitable for
exterior use.
5. What is the primary responsibility of a carpentry supervisor?
A. Performing all carpentry tasks
B. Ordering materials only
C. Directing, coordinating, and inspecting work
D. Drafting architectural plans
Rationale: Supervisors oversee workers, ensure quality, and
coordinate tasks.
, 6. What safety equipment is required when operating a table saw?
A. Hard hat only
B. Dust mask only
C. Eye and hearing protection
D. Gloves only
Rationale: Table saws pose risks of flying debris and loud noise.
7. Which material is commonly used for concrete formwork?
A. MDF
B. Plywood
C. Particleboard
D. OSB only
Rationale: Plywood is strong, reusable, and resists moisture when
properly treated.
8. What is the standard spacing for wall studs in most construction?
A. 12 inches on center
B. 16 inches on center
C. 18 inches on center
D. 24 inches on center
Rationale: 16 inches on center is the most common standard for
strength and material efficiency.
9. Which blueprint symbol usually indicates a door?
A. Solid rectangle
B. Circle with X
Practice Questions And Correct Answers
(Verified Answers) Plus Rationales 2026
Q&A | Instant Download Pdf
1. Which tool is best used to check if a door frame is perfectly vertical?
A. Tape measure
B. Chalk line
C. Level
D. Framing square
Rationale: A level is specifically designed to determine plumb
(vertical) and level (horizontal) alignment.
2. What type of wood joint is most commonly used for framing walls?
A. Dovetail joint
B. Butt joint
C. Mortise and tenon
D. Lap joint
Rationale: Butt joints are simple and efficient, making them standard
for wall framing.
,3. In supervising carpentry work, which document outlines scope,
materials, and workmanship standards?
A. Time sheet
B. Safety log
C. Construction specifications
D. Inventory list
Rationale: Specifications define required materials, methods, and
quality standards.
4. Which nail is most appropriate for exterior decking?
A. Common steel nail
B. Galvanized nail
C. Finish nail
D. Brad nail
Rationale: Galvanized nails resist corrosion, making them suitable for
exterior use.
5. What is the primary responsibility of a carpentry supervisor?
A. Performing all carpentry tasks
B. Ordering materials only
C. Directing, coordinating, and inspecting work
D. Drafting architectural plans
Rationale: Supervisors oversee workers, ensure quality, and
coordinate tasks.
, 6. What safety equipment is required when operating a table saw?
A. Hard hat only
B. Dust mask only
C. Eye and hearing protection
D. Gloves only
Rationale: Table saws pose risks of flying debris and loud noise.
7. Which material is commonly used for concrete formwork?
A. MDF
B. Plywood
C. Particleboard
D. OSB only
Rationale: Plywood is strong, reusable, and resists moisture when
properly treated.
8. What is the standard spacing for wall studs in most construction?
A. 12 inches on center
B. 16 inches on center
C. 18 inches on center
D. 24 inches on center
Rationale: 16 inches on center is the most common standard for
strength and material efficiency.
9. Which blueprint symbol usually indicates a door?
A. Solid rectangle
B. Circle with X
