Massachusetts 1A Hoisting License EXAM STUDY
GUIDE 2026/2027 COMPLETE QUESTIONS WITH
VERIFIED CORRECT ANSWERS || 100%
GUARANTEED PASS <NEWEST VERSION>
Save
Terms in this set (152)
Where should a license or temporary Shall be carried ON the person at all times; in the
permit be located during time of case of a temporary permit the person shall also
operation of equipment carry their drivers license
Whats the fine for violating section No less than $500 and no more than $3,000, or by
53, 53a or 54 imprisonment of no more than 3 months, or both
fine and imprisonment
Whats the fine for permitting an No less than $1,000 and no more than $3,000, or
unlicensed person to operate imprisonment of no more than 3 months, or both
machinery fine and imprisonment
Whats the fine for violating section No less than $10 no more than $300, or by
42 to 51, or prevents an inspector imprisonment of upto 3 months
from entering the premises
,Whats the purpose of 520CMR 6.00 To establish reasonable requirements to protect
the public safety of the citizens of the
commonwealth from the hazards inherent in the
operation of housting machinery by establishing
min standards neccessary to obtain a hoisting
machinery operators license or temp permit
ANSI American National Standards Institute
Apprentice license A document issued by the dept upon proof of
registratio at a training facility and with the division
of apprentice training within the dept of labor
standards, which enables the holder to operate
hoisting machinery under the direct guidance and
supervision of a duly licensed person licensed to
operate the category of hoisting machinery for
which documentation is issued
ASME American Society of Mechanical Engineers
cargo A load, quantity or volume that can be processed
or transported
Apprentice licensee A person, 18 or older, registered with the dept of
labor standards and has obtained an apprentice
license to operate while under direct guidance and
supervision of a duly licensed person
Chief The chief of inspections-mechanical of the dept of
public safety
,Compact hoisting machinery Machinery wirh a gross vehicle weight not
exceeding 10,000 lbs, excluding Class 1, Class 3 and
Class 4 hoisting machinery as listed in 520CMR 6.10.
Machinery operated under temp permit may not
exceed 8,000lbs
DAT Division of Apprentice Training
Department Dept of Public Safety
DOT Department of Transportation
Emergency procedure Actions required to be taken when imminent
danger may occur to prevent damage to life,
property, or to public safety
Company license Issued by an exempt company that has a dept
approved in service training program and is only
valid for machinery used on company property
fork lift Any mobile powered truck used to carry, push, lift,
stack or tier materials, EXCLUDING earth moving,
over the road haulage trucks and equipment which
was designed to move earth but modified to
accept forks
, Hoisting machinery Derricks, cableways, machinery used for
discharging cargoes, and temp elevator cars used
on excavation work or hoisting building materials,
when the motive power to operate such machinery
is mechanical and other than steam, and any other
equipment that has the MIN capability of hoisting a
load HIGHER THAN 10 FT, and either the capability
of lifting loads GREATER THAN 500 LBS or the
capacity of the bucket EXCEEDS 1/4 CUBIC YARDS;
overhead bridge cranes, electric or air driven
hoists, specialty equipment as catagorized under
520CMR 6.00
incedent A situation that results in serious injury, property
damage or any condition that is necessary for the
preservation of the public health or safety
Injury and incedent documentation A form furnished by the department detailing all
specific info regarding any serious injury, property
damage or mechanical failure that may have
occurred
inspector A District Engineering Inspector employed by the
Department
Manufacturer approved attachment Attachable equipment tailored to perform a
particular task, designed or approved for use in
accordance with the equipment manufacturers
spec's. If the manufacturer doesnt exist, a MASS
registered professional engineer shall review and
approve in writing the actions and reasons for said
specs to the attachable equipment
GUIDE 2026/2027 COMPLETE QUESTIONS WITH
VERIFIED CORRECT ANSWERS || 100%
GUARANTEED PASS <NEWEST VERSION>
Save
Terms in this set (152)
Where should a license or temporary Shall be carried ON the person at all times; in the
permit be located during time of case of a temporary permit the person shall also
operation of equipment carry their drivers license
Whats the fine for violating section No less than $500 and no more than $3,000, or by
53, 53a or 54 imprisonment of no more than 3 months, or both
fine and imprisonment
Whats the fine for permitting an No less than $1,000 and no more than $3,000, or
unlicensed person to operate imprisonment of no more than 3 months, or both
machinery fine and imprisonment
Whats the fine for violating section No less than $10 no more than $300, or by
42 to 51, or prevents an inspector imprisonment of upto 3 months
from entering the premises
,Whats the purpose of 520CMR 6.00 To establish reasonable requirements to protect
the public safety of the citizens of the
commonwealth from the hazards inherent in the
operation of housting machinery by establishing
min standards neccessary to obtain a hoisting
machinery operators license or temp permit
ANSI American National Standards Institute
Apprentice license A document issued by the dept upon proof of
registratio at a training facility and with the division
of apprentice training within the dept of labor
standards, which enables the holder to operate
hoisting machinery under the direct guidance and
supervision of a duly licensed person licensed to
operate the category of hoisting machinery for
which documentation is issued
ASME American Society of Mechanical Engineers
cargo A load, quantity or volume that can be processed
or transported
Apprentice licensee A person, 18 or older, registered with the dept of
labor standards and has obtained an apprentice
license to operate while under direct guidance and
supervision of a duly licensed person
Chief The chief of inspections-mechanical of the dept of
public safety
,Compact hoisting machinery Machinery wirh a gross vehicle weight not
exceeding 10,000 lbs, excluding Class 1, Class 3 and
Class 4 hoisting machinery as listed in 520CMR 6.10.
Machinery operated under temp permit may not
exceed 8,000lbs
DAT Division of Apprentice Training
Department Dept of Public Safety
DOT Department of Transportation
Emergency procedure Actions required to be taken when imminent
danger may occur to prevent damage to life,
property, or to public safety
Company license Issued by an exempt company that has a dept
approved in service training program and is only
valid for machinery used on company property
fork lift Any mobile powered truck used to carry, push, lift,
stack or tier materials, EXCLUDING earth moving,
over the road haulage trucks and equipment which
was designed to move earth but modified to
accept forks
, Hoisting machinery Derricks, cableways, machinery used for
discharging cargoes, and temp elevator cars used
on excavation work or hoisting building materials,
when the motive power to operate such machinery
is mechanical and other than steam, and any other
equipment that has the MIN capability of hoisting a
load HIGHER THAN 10 FT, and either the capability
of lifting loads GREATER THAN 500 LBS or the
capacity of the bucket EXCEEDS 1/4 CUBIC YARDS;
overhead bridge cranes, electric or air driven
hoists, specialty equipment as catagorized under
520CMR 6.00
incedent A situation that results in serious injury, property
damage or any condition that is necessary for the
preservation of the public health or safety
Injury and incedent documentation A form furnished by the department detailing all
specific info regarding any serious injury, property
damage or mechanical failure that may have
occurred
inspector A District Engineering Inspector employed by the
Department
Manufacturer approved attachment Attachable equipment tailored to perform a
particular task, designed or approved for use in
accordance with the equipment manufacturers
spec's. If the manufacturer doesnt exist, a MASS
registered professional engineer shall review and
approve in writing the actions and reasons for said
specs to the attachable equipment
