1|Page
c-201 Electrical Systems 1 SACA Certification Exam
,Most Recent Exam||Verified Exam!! ||2026 Actual
Complete Real Exam Questions With verified Answers
(Correct Answers) Already Graded A+, Guaranteed
success!!!
What should you do before working on electrical
equipment? - Answers-Lock out tag out(LOTO)
What is normally not measured on a digital multi meter? -
Answers-Frequency
Main line current formula in parallel - Answers-1/
1/R1+1/R2+1/R3
What is indicated when voltage is measured across the
contacts of a switch - Answers-Its open
What type of transformer is used to get two 120 volt lines
from a 480 volt source? - Answers-4:1 center tap
What is the effect of a capacitor in a DC circuit in a parallel
circuit? - Answers-Aids voltage change
,2|Page
What is the immediate danger of unsecured electrical
cords? - Answers-Trip hazard
Why does most electrical utility power go throughout the
world use AC instead of DC? - Answers-AC is better for
transmitting longer distances and it is cheaper to generate.
When should a fuse be replaced? - Answers-When there
is no continuity
What type of voltage divider is normally used when the
load resistance is relatively low? - Answers-Loaded
voltage divider
What action should be taken when a circuit breaker trips?
- Answers-Off then on
If you add a third capacitor in series with two other
capacitors, what would happen to total capacitance and
current. - Answers-The current and capacitance would
decrease
, 3|Page
Where are the meter leads placed in a circuit to measure
current in a single component or device. - Answers-In
series
Which type of circuit breaker has a delay before it trips. -
Answers-Thermal circuit breaker
Which output creates a sound as its primary output? -
Answers-Buzzer
What is the best method to verify a piece of equipment is
properly grounded? - Answers-Use of multimeter and
check for an open current
What feature of a ground circuit creates a safe path for
current? - Answers-Low resistance path, connection to
earth or ground point
What steps should be taken to correctly measure the
resistance of a resister that is wired in a circuit? -
Answers-Disconnect one end and power should be off
c-201 Electrical Systems 1 SACA Certification Exam
,Most Recent Exam||Verified Exam!! ||2026 Actual
Complete Real Exam Questions With verified Answers
(Correct Answers) Already Graded A+, Guaranteed
success!!!
What should you do before working on electrical
equipment? - Answers-Lock out tag out(LOTO)
What is normally not measured on a digital multi meter? -
Answers-Frequency
Main line current formula in parallel - Answers-1/
1/R1+1/R2+1/R3
What is indicated when voltage is measured across the
contacts of a switch - Answers-Its open
What type of transformer is used to get two 120 volt lines
from a 480 volt source? - Answers-4:1 center tap
What is the effect of a capacitor in a DC circuit in a parallel
circuit? - Answers-Aids voltage change
,2|Page
What is the immediate danger of unsecured electrical
cords? - Answers-Trip hazard
Why does most electrical utility power go throughout the
world use AC instead of DC? - Answers-AC is better for
transmitting longer distances and it is cheaper to generate.
When should a fuse be replaced? - Answers-When there
is no continuity
What type of voltage divider is normally used when the
load resistance is relatively low? - Answers-Loaded
voltage divider
What action should be taken when a circuit breaker trips?
- Answers-Off then on
If you add a third capacitor in series with two other
capacitors, what would happen to total capacitance and
current. - Answers-The current and capacitance would
decrease
, 3|Page
Where are the meter leads placed in a circuit to measure
current in a single component or device. - Answers-In
series
Which type of circuit breaker has a delay before it trips. -
Answers-Thermal circuit breaker
Which output creates a sound as its primary output? -
Answers-Buzzer
What is the best method to verify a piece of equipment is
properly grounded? - Answers-Use of multimeter and
check for an open current
What feature of a ground circuit creates a safe path for
current? - Answers-Low resistance path, connection to
earth or ground point
What steps should be taken to correctly measure the
resistance of a resister that is wired in a circuit? -
Answers-Disconnect one end and power should be off
