MSF Motorcycle Safety Foundation E-Course
Comprehensive Resource To Help You Ace 2026-2027
Includes Frequently Tested Questions With ELABORATED
100% Correct COMPLETE SOLUTIONS
Guaranteed Pass First Attempt!!
Current Update!!
1. What does FINE-C refer to?
Answer: An engine pre-start routine.
2. What does FINE-C stand for?
Answer: Fuel, Ignition, Neutral, Engine cut-off switch, Choke, Clutch.
3. What does the “F” in FINE-C indicate?
Answer: Fuel — turn the fuel supply valve on (if equipped).
4. What does the “I” in FINE-C indicate?
Answer: Ignition — turn the ignition switch to the ON position; indicator
lights should illuminate.
5. What does the “N” in FINE-C indicate?
Answer: Neutral — the green neutral indicator light should be on.
6. What does the “E” in FINE-C indicate?
Answer: Engine cut-off switch — place it in the RUN/ON position.
7. What does the “C” in FINE-C indicate?
Answer: Choke and Clutch — set the choke (if cold) and squeeze the clutch
lever.
8. When starting the engine, at least one ______ should be applied.
Answer: Brake.
, 9. Why should the throttle not be used when the choke is ON?
Answer: It can supply too much fuel to the engine.
10.After the engine starts, which lever may be released slowly and why?
Answer: The clutch lever, in case the motorcycle is not in neutral.
11.Why should you keep your hand on the clutch when starting the engine?
Answer: The motorcycle may be in gear.
12.Where is the throttle located?
Answer: On the right-hand grip.
13.What does it mean to “roll on” the throttle?
Answer: Twist the throttle toward you to maintain or slightly increase
speed.
14.Where is the clutch lever located?
Answer: On the left-hand grip.
15.What happens when the clutch lever is fully squeezed?
Answer: No power is transmitted to the rear wheel.
16.Where is the gearshift located?
Answer: On the left footrest.
17.How do you operate the gearshift?
Answer: Lift up for a higher gear; press down for a lower gear.
18.How far does the foot need to move when shifting gears?
Answer: About an inch or so.
Comprehensive Resource To Help You Ace 2026-2027
Includes Frequently Tested Questions With ELABORATED
100% Correct COMPLETE SOLUTIONS
Guaranteed Pass First Attempt!!
Current Update!!
1. What does FINE-C refer to?
Answer: An engine pre-start routine.
2. What does FINE-C stand for?
Answer: Fuel, Ignition, Neutral, Engine cut-off switch, Choke, Clutch.
3. What does the “F” in FINE-C indicate?
Answer: Fuel — turn the fuel supply valve on (if equipped).
4. What does the “I” in FINE-C indicate?
Answer: Ignition — turn the ignition switch to the ON position; indicator
lights should illuminate.
5. What does the “N” in FINE-C indicate?
Answer: Neutral — the green neutral indicator light should be on.
6. What does the “E” in FINE-C indicate?
Answer: Engine cut-off switch — place it in the RUN/ON position.
7. What does the “C” in FINE-C indicate?
Answer: Choke and Clutch — set the choke (if cold) and squeeze the clutch
lever.
8. When starting the engine, at least one ______ should be applied.
Answer: Brake.
, 9. Why should the throttle not be used when the choke is ON?
Answer: It can supply too much fuel to the engine.
10.After the engine starts, which lever may be released slowly and why?
Answer: The clutch lever, in case the motorcycle is not in neutral.
11.Why should you keep your hand on the clutch when starting the engine?
Answer: The motorcycle may be in gear.
12.Where is the throttle located?
Answer: On the right-hand grip.
13.What does it mean to “roll on” the throttle?
Answer: Twist the throttle toward you to maintain or slightly increase
speed.
14.Where is the clutch lever located?
Answer: On the left-hand grip.
15.What happens when the clutch lever is fully squeezed?
Answer: No power is transmitted to the rear wheel.
16.Where is the gearshift located?
Answer: On the left footrest.
17.How do you operate the gearshift?
Answer: Lift up for a higher gear; press down for a lower gear.
18.How far does the foot need to move when shifting gears?
Answer: About an inch or so.
