UPDATE!!!!2025/2026|GUARANTEED PASS|GRADED
To screw gypsum panels to 18 gage steel studs, you should use what type of screw? -
ANSWER S-12
A mil gage is used to verify___________. - ANSWER coating thickness
A contractor is building a 40' x 24' single story house with a 6/12 straight gable roof and a
96" from sole plate to top plate. How many 4' x 8' sheets of wall sheathing are required. Do
not deduct openings or add waste. - ANSWER 37
What item is not part of an exterior frame wall - ANSWER Bridging
Where is the base flashing installed when using brick veneer for the outside finish over
wood frame walls? - ANSWER Between the sheathing paper and the wood sheathing,
extending into the mortar joint at the brick course below the bottom of the sheathing.
What angle does the valley rafter form with the main ridge board in a roof of uniform pitch?
- ANSWER 45
What is the rafter run for a straight gable roof with a span of 36'? - ANSWER 18'
In what section of the construction manual with information on artifacts be likely shown? -
ANSWER Supplemental
1
, What is the type of roofing in which skip sheathing is used? - ANSWER Wood shingles
and shakes
Carpentry & Building Construction
Page 565
The windows manufacturer's catalog will contain a sizing table with what measurements? -
ANSWER Masonry opening, rough opening, frame size, glass size, and occasionally
sash size
Carpentry & Building Construction
page 586
When placing insulation in an existing home what is the best installation method? -
ANSWER Loose-fill
Carpentry & Building Construction
page 898
How does batt insulation located under the floor joist stay in place? - ANSWER Wire
mesh or rigid board
Carpentry & Building Construction
page 904-905
Drywall can cover wall cavities once the moisture content of the insulation drops to less
than? - ANSWER 19%
Carpentry & Building Construction
page 899
Using a 1/4" scale, what does 3 1/2" represent? - ANSWER 14 feet
Carpentry & Building Construction
page 44
2
To screw gypsum panels to 18 gage steel studs, you should use what type of screw? -
ANSWER S-12
A mil gage is used to verify___________. - ANSWER coating thickness
A contractor is building a 40' x 24' single story house with a 6/12 straight gable roof and a
96" from sole plate to top plate. How many 4' x 8' sheets of wall sheathing are required. Do
not deduct openings or add waste. - ANSWER 37
What item is not part of an exterior frame wall - ANSWER Bridging
Where is the base flashing installed when using brick veneer for the outside finish over
wood frame walls? - ANSWER Between the sheathing paper and the wood sheathing,
extending into the mortar joint at the brick course below the bottom of the sheathing.
What angle does the valley rafter form with the main ridge board in a roof of uniform pitch?
- ANSWER 45
What is the rafter run for a straight gable roof with a span of 36'? - ANSWER 18'
In what section of the construction manual with information on artifacts be likely shown? -
ANSWER Supplemental
1
, What is the type of roofing in which skip sheathing is used? - ANSWER Wood shingles
and shakes
Carpentry & Building Construction
Page 565
The windows manufacturer's catalog will contain a sizing table with what measurements? -
ANSWER Masonry opening, rough opening, frame size, glass size, and occasionally
sash size
Carpentry & Building Construction
page 586
When placing insulation in an existing home what is the best installation method? -
ANSWER Loose-fill
Carpentry & Building Construction
page 898
How does batt insulation located under the floor joist stay in place? - ANSWER Wire
mesh or rigid board
Carpentry & Building Construction
page 904-905
Drywall can cover wall cavities once the moisture content of the insulation drops to less
than? - ANSWER 19%
Carpentry & Building Construction
page 899
Using a 1/4" scale, what does 3 1/2" represent? - ANSWER 14 feet
Carpentry & Building Construction
page 44
2
