BMW Associate Level ASE Test – BMW
Group Training – Associate Technician
Exam Practice Questions and Answers
Introduction:
This document contains a comprehensive collection of BMW
Associate Level ASE-style test questions with correct answers,
covering core technician knowledge required for BMW
associate certification. Topics include CPO inspections,
electrical diagnostics, braking systems, safety procedures,
ISTA/TIS usage, warranty policies, and general automotive
troubleshooting aligned with BMW training standards.
Exam Questions and Answers:
A technician should consider which of the following questions
for a quality control process after performing service work to a
vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above - -ANSWER:-All of the above
,While performing a CPO inspection, a technician finds the car
has an aftermarket LED headlight installed. The technician
should: - -ANSWER:-Fail the CPO inspection or replace the
Headlighits
What is the importance of having the engine at operating
temperature when performing an oil service?
Drains oil faster
Removes more contaminants
The repair instructions say to do it
All of the above - -ANSWER:-All of the above
What is the minimum road test distance for a CPO inspection? -
-ANSWER:-5 miles
Regarding BMW wiper service mode.
Technician A says that on F and G series vehicles it is
necessary to place the wipers in service mode prior to
removing the wiper blades.
, Technician B says that on a G series vehicle; activate the
vehicle by pressing the start/stop button. Then deactivate the
vehicle by pressing the start/stop button again within 3
seconds. Then hold the wiper stalk in the up position.
Who is correct? - -ANSWER:-A only
Engine oil Top-up services may be reimbursed under the terms
of the BMW Maintenance Program when it is "active" on the
vehicle. - -ANSWER:-True
During a CPO inspection, a front brake pad measurement is
taken of 4mm on the left inner pad and 7mm on the left outer
pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed
specifications.
Who is correct? - -ANSWER:-Neither A or B
Group Training – Associate Technician
Exam Practice Questions and Answers
Introduction:
This document contains a comprehensive collection of BMW
Associate Level ASE-style test questions with correct answers,
covering core technician knowledge required for BMW
associate certification. Topics include CPO inspections,
electrical diagnostics, braking systems, safety procedures,
ISTA/TIS usage, warranty policies, and general automotive
troubleshooting aligned with BMW training standards.
Exam Questions and Answers:
A technician should consider which of the following questions
for a quality control process after performing service work to a
vehicle?
Did I address all concerns?
Did I top off all fluids and set tire pressure?
Did I reset service lights?
All of the above - -ANSWER:-All of the above
,While performing a CPO inspection, a technician finds the car
has an aftermarket LED headlight installed. The technician
should: - -ANSWER:-Fail the CPO inspection or replace the
Headlighits
What is the importance of having the engine at operating
temperature when performing an oil service?
Drains oil faster
Removes more contaminants
The repair instructions say to do it
All of the above - -ANSWER:-All of the above
What is the minimum road test distance for a CPO inspection? -
-ANSWER:-5 miles
Regarding BMW wiper service mode.
Technician A says that on F and G series vehicles it is
necessary to place the wipers in service mode prior to
removing the wiper blades.
, Technician B says that on a G series vehicle; activate the
vehicle by pressing the start/stop button. Then deactivate the
vehicle by pressing the start/stop button again within 3
seconds. Then hold the wiper stalk in the up position.
Who is correct? - -ANSWER:-A only
Engine oil Top-up services may be reimbursed under the terms
of the BMW Maintenance Program when it is "active" on the
vehicle. - -ANSWER:-True
During a CPO inspection, a front brake pad measurement is
taken of 4mm on the left inner pad and 7mm on the left outer
pad.
Technician A says the pads are within specifications.
Technician B says the inner pad is at the minimum allowed
specifications.
Who is correct? - -ANSWER:-Neither A or B
