1|Page
Georgia Water Distribution Study Guide Exam , Most
Recent 2026 Actual Complete Real Verified Exam
Questions And Verified Answers | 100% Correct
Answers | Graded A+ ||Guaranteed Success!! Newest
Exam!!!
Who enforces the drinking water regulations in Georgia? -
Answer-Georgia EPD
What type of sample is required for bacterial analysis? -
Answer-Flushed
What type of sample is required for lead and copper? -
Answer-First Draw
Water must sit in the customer's plumbing lines motionless
for at least 6 hours, but no longer than 12 hour for which of
the following samples? - Answer-Lead & Copper
Care must be taken when handling bacteria sample
bottles during the sampling process due to the fact that
they are: - Answer-Sterile
,2|Page
What water quality problem is most likely to occur dead-
end water mains? - Answer-Dirty Water and or Taste &
Odor
Examples of three waterborne diseases are: - Answer-
Typhoid fever, Infectious hepatitis, Cholera
When should a new water main be flushed and disinfected
before placing in service? - Answer-Every Time
The standard purity of HTH is - Answer-65%
Sodium hypochlorite is also known as - Answer-Bleach
The chemical used to detect chlorine residuals in water is -
Answer-DPD
A venturi tube increases the velocity and decreases the
pressure as water flows through the unit. This type of tube
is used to: - Answer-Measure the rate of water flowing
through it
,3|Page
Which one of the following types of meters has no moving
parts: - Answer-Venturi
Which tap is a connection made into a main that is full of
water or under pressure? - Answer-Wet Tap
A valve that joins a customer's service to the water main
called: - Answer-Corporation Stop
The following meter is used where the water demand
varies considerably: - Answer-Compound
Which if the following factors determine the type of
corporation stop that should be used? - Answer-Size and
material of main being tapped, Service line material, Type
of connection to service line
Which of the following is an advantage of wet taps? -
Answer-No interruption in service, Made without shutting
off the water, Less chance of contamination
The most commonly known corporation stop thread is
called: - Answer-Mueller Threads
, 4|Page
Ab example of a large-flow water main is - Answer-Velocity
Meter
Temporary cloudiness in a freshly drawn sample of tap
water may be caused by: - Answer-Air
When opening and closing valves in high pressure lines
the valves should be: - Answer-Opened and closed slowly
Which of the following is NOT a joint used to install
valves? - Answer-Actuator Joint
Which valve is never used for throttling flow? - Answer-
Gate valve
A valve that is leak-tight is said to be - Answer-Resilient
The connection between a safe and unsafe water supply
is called a: - Answer-Cross Connection
Georgia Water Distribution Study Guide Exam , Most
Recent 2026 Actual Complete Real Verified Exam
Questions And Verified Answers | 100% Correct
Answers | Graded A+ ||Guaranteed Success!! Newest
Exam!!!
Who enforces the drinking water regulations in Georgia? -
Answer-Georgia EPD
What type of sample is required for bacterial analysis? -
Answer-Flushed
What type of sample is required for lead and copper? -
Answer-First Draw
Water must sit in the customer's plumbing lines motionless
for at least 6 hours, but no longer than 12 hour for which of
the following samples? - Answer-Lead & Copper
Care must be taken when handling bacteria sample
bottles during the sampling process due to the fact that
they are: - Answer-Sterile
,2|Page
What water quality problem is most likely to occur dead-
end water mains? - Answer-Dirty Water and or Taste &
Odor
Examples of three waterborne diseases are: - Answer-
Typhoid fever, Infectious hepatitis, Cholera
When should a new water main be flushed and disinfected
before placing in service? - Answer-Every Time
The standard purity of HTH is - Answer-65%
Sodium hypochlorite is also known as - Answer-Bleach
The chemical used to detect chlorine residuals in water is -
Answer-DPD
A venturi tube increases the velocity and decreases the
pressure as water flows through the unit. This type of tube
is used to: - Answer-Measure the rate of water flowing
through it
,3|Page
Which one of the following types of meters has no moving
parts: - Answer-Venturi
Which tap is a connection made into a main that is full of
water or under pressure? - Answer-Wet Tap
A valve that joins a customer's service to the water main
called: - Answer-Corporation Stop
The following meter is used where the water demand
varies considerably: - Answer-Compound
Which if the following factors determine the type of
corporation stop that should be used? - Answer-Size and
material of main being tapped, Service line material, Type
of connection to service line
Which of the following is an advantage of wet taps? -
Answer-No interruption in service, Made without shutting
off the water, Less chance of contamination
The most commonly known corporation stop thread is
called: - Answer-Mueller Threads
, 4|Page
Ab example of a large-flow water main is - Answer-Velocity
Meter
Temporary cloudiness in a freshly drawn sample of tap
water may be caused by: - Answer-Air
When opening and closing valves in high pressure lines
the valves should be: - Answer-Opened and closed slowly
Which of the following is NOT a joint used to install
valves? - Answer-Actuator Joint
Which valve is never used for throttling flow? - Answer-
Gate valve
A valve that is leak-tight is said to be - Answer-Resilient
The connection between a safe and unsafe water supply
is called a: - Answer-Cross Connection
