FDOT ASPHALT PAVING LEVEL 2 2026-
2027 NEWEST QUESTIONS AND
CORRECT ANSWERS | A+ GRADE
VERIFIED ANSWERS
If the FC-5 friction course aggregate is cracking under the
weight of the roller:
A. Is the PLI of the roller between 135 and 200?
B. Is the roller driving on a cool mat?
C. Is the temperature of the mix too high?
D. All of the above
E. Both A & B Correct Answer (A.) - Is the PLI of the roller
between 135 and 200?
Which mix will be easier to compact over a milled surface?
A. An SP-12.5 mix placed 3/4 inch thick?
B. An SP-12.5 mix placed 1 inch thick?
C. An SP-12.5 mix placed 1 1/2 inches thick?
D. None of the above Correct Answer (A.) An SP-12.5 mix
placed 3/4 inches thick
Given: Target Spread Rate: 165 lbs/Sq yds
Given: Truck Weights (tons): 18.2, 19.63, 17.56, 18.78,
19.55
Given: Lane R1, Lift 1
Given: Start Station: 5+98 End Station: 13+60
Given: Lane Width: 13.5 feet
,What is the calculated application rate? (lbs/sq yds)
Correct Answer (E.) 164.0 lbs/sq yds
Given: Target Spread Rate: 165 lbs/Sq yds
Given: Truck Weights (tons): 18.2, 19.63, 17.56, 18.78,
19.55
Given: Lane R1, Lift 1
Given: Start Station: 5+98 End Station: 13+60
Given: Lane Width: 13.5 feet
What do you do? (Spread Rate) Correct Answer (A.)
Spread Rate is in tolerance - document and continue
Properly operated, the __ should be moving 80%-90% of
the time while paving. Correct Answer (C.) Augers
Cover Stone for an ARMI layer must be applied at what
application rate?
A. 0.6 to 0.8 ft³/yd²
B. 0.26 to 0.33 ft³/yd²
C. 0.34 to 0.57 ft³/yd²
D. 0.02 to 0.08 ft³/yd²
E. Not a specification requirement Correct Answer (B.)
0.26 to 0.33 ft³/yd²
(T/F:) Increasing the layer thickness affects the time
available for compaction more than increasing the mix
temperature. Correct Answer True
, Using the classroom Project Core Layout Example -
Method B from Module 8 - What are the station numbers
for Cores 3-2-1 (576 tons) and 3-2-2 (673 tons)?
Given Information: Starting Sta. is 10+00, Paving direction
is "Up-Station", Spread rate is 165 lbs/yd², lane width is 12
feet Correct Answer (C.) 52+36, 61+18
Calculate the tack spread rate using the chart from
Appendix 1. Given Information: Type of Tack RS-1h, Mix
being placed on milled surface. Complete the calculations
using the given information.
What is the calculated application rate? (gal/yd²)
Ending Sta.: 103+60; Beginning Sta.: 87+42; End
Reading: 26/6; Beginning Reading: 22/1; Width of
Application: 12 feet; Temp of Tack (Emulsified): 180°F
Correct Answer 0.05 gal/yd²
Calculate the tack spread rate using the chart from
Appendix 1. Given Information: Type of Tack RS-1h, Mix
being placed on milled surface. Complete the calculations
using the given information.
What do you do?
Ending Sta.: 103+60; Beginning Sta.: 87+42; End
Reading: 26/6; Beginning Reading: 22/1; Width of
Application: 12 feet; Temp of Tack (Emulsified): 180°F
Correct Answer (C.) Spread rate is in specification -
document and continue
2027 NEWEST QUESTIONS AND
CORRECT ANSWERS | A+ GRADE
VERIFIED ANSWERS
If the FC-5 friction course aggregate is cracking under the
weight of the roller:
A. Is the PLI of the roller between 135 and 200?
B. Is the roller driving on a cool mat?
C. Is the temperature of the mix too high?
D. All of the above
E. Both A & B Correct Answer (A.) - Is the PLI of the roller
between 135 and 200?
Which mix will be easier to compact over a milled surface?
A. An SP-12.5 mix placed 3/4 inch thick?
B. An SP-12.5 mix placed 1 inch thick?
C. An SP-12.5 mix placed 1 1/2 inches thick?
D. None of the above Correct Answer (A.) An SP-12.5 mix
placed 3/4 inches thick
Given: Target Spread Rate: 165 lbs/Sq yds
Given: Truck Weights (tons): 18.2, 19.63, 17.56, 18.78,
19.55
Given: Lane R1, Lift 1
Given: Start Station: 5+98 End Station: 13+60
Given: Lane Width: 13.5 feet
,What is the calculated application rate? (lbs/sq yds)
Correct Answer (E.) 164.0 lbs/sq yds
Given: Target Spread Rate: 165 lbs/Sq yds
Given: Truck Weights (tons): 18.2, 19.63, 17.56, 18.78,
19.55
Given: Lane R1, Lift 1
Given: Start Station: 5+98 End Station: 13+60
Given: Lane Width: 13.5 feet
What do you do? (Spread Rate) Correct Answer (A.)
Spread Rate is in tolerance - document and continue
Properly operated, the __ should be moving 80%-90% of
the time while paving. Correct Answer (C.) Augers
Cover Stone for an ARMI layer must be applied at what
application rate?
A. 0.6 to 0.8 ft³/yd²
B. 0.26 to 0.33 ft³/yd²
C. 0.34 to 0.57 ft³/yd²
D. 0.02 to 0.08 ft³/yd²
E. Not a specification requirement Correct Answer (B.)
0.26 to 0.33 ft³/yd²
(T/F:) Increasing the layer thickness affects the time
available for compaction more than increasing the mix
temperature. Correct Answer True
, Using the classroom Project Core Layout Example -
Method B from Module 8 - What are the station numbers
for Cores 3-2-1 (576 tons) and 3-2-2 (673 tons)?
Given Information: Starting Sta. is 10+00, Paving direction
is "Up-Station", Spread rate is 165 lbs/yd², lane width is 12
feet Correct Answer (C.) 52+36, 61+18
Calculate the tack spread rate using the chart from
Appendix 1. Given Information: Type of Tack RS-1h, Mix
being placed on milled surface. Complete the calculations
using the given information.
What is the calculated application rate? (gal/yd²)
Ending Sta.: 103+60; Beginning Sta.: 87+42; End
Reading: 26/6; Beginning Reading: 22/1; Width of
Application: 12 feet; Temp of Tack (Emulsified): 180°F
Correct Answer 0.05 gal/yd²
Calculate the tack spread rate using the chart from
Appendix 1. Given Information: Type of Tack RS-1h, Mix
being placed on milled surface. Complete the calculations
using the given information.
What do you do?
Ending Sta.: 103+60; Beginning Sta.: 87+42; End
Reading: 26/6; Beginning Reading: 22/1; Width of
Application: 12 feet; Temp of Tack (Emulsified): 180°F
Correct Answer (C.) Spread rate is in specification -
document and continue
