SACA Certification C-101 EXAM
QUESTIONS WITH CORRECT
SOLUTIONS||100% GUARANTEED
PASS||UPDATED 2026/2027
SYLLABUS||A+ GRADED||<<NEWEST
VERSION>>
The three most basic dimensions identified on drawings are __________. -
ANSWER ✓ Width, depth, height
The basic dimensions shown on a print are called __________ dimensions. -
ANSWER ✓ Nominal
If a product feature has a dimension of 1.8 ± .03, what is the lower tolerance
dimension? - ANSWER ✓ 1.77
Internal dimensions, like holes, are at their MMC when they are at their
__________ of their tolerance zone? - ANSWER ✓ Lower limit
What tolerance condition is the smallest amount of material in a part? - ANSWER
✓ LMC
What is the difference between allowance and clearance? - ANSWER ✓
Allowance is the tightest possible fit, while clearance is the loosest possible fit.
Using datums helps eliminate __________. - ANSWER ✓ Errors in measurement
What is the difference between local and general notes on a blueprint? -
ANSWER ✓ Local notes apply to specific items or areas, while general notes
apply to the entire drawing
What type of drawing defines how the product is going to be manufactured? -
ANSWER ✓ Process drawing
, How is a half scale drawing written? - ANSWER ✓ 1:2
Which of the following lists the proper digital caliper calibration steps in order? -
ANSWER ✓ Turn on the caliper display, close the jaws, press the zero button
Why are dial calipers the most widely used precision measuring instrument on the
shop floor? - ANSWER ✓ They are easy to carry
They take measurements quickly
They are reasonably accurate
How often should a micrometer's calibration be checked? - ANSWER ✓ Every
few months
Which of the following items can affect a micrometer's measurement? - ANSWER
✓ Dust
Oil
Shavings
Burrs
Force is any attempt to change the motion of an object and is measured in
__________. - ANSWER ✓ Newtons (N) and pound-force (lbf)
Potential energy is stored energy until it is allowed to move, then it becomes
__________. - ANSWER ✓ Kinetic energy
Mass is the amount of __________ the object contains. - ANSWER ✓ Matter
Air supplied to a pneumatic system is supplied through the __________ line. -
ANSWER ✓ Supply
A(n) __________ provides power to a hydraulic system by pumping oil from a
reservoir into the supply lines.. - ANSWER ✓ Pump
What can compressed air that is less than 30 psi be used for? - ANSWER ✓
Cleaning work areas
QUESTIONS WITH CORRECT
SOLUTIONS||100% GUARANTEED
PASS||UPDATED 2026/2027
SYLLABUS||A+ GRADED||<<NEWEST
VERSION>>
The three most basic dimensions identified on drawings are __________. -
ANSWER ✓ Width, depth, height
The basic dimensions shown on a print are called __________ dimensions. -
ANSWER ✓ Nominal
If a product feature has a dimension of 1.8 ± .03, what is the lower tolerance
dimension? - ANSWER ✓ 1.77
Internal dimensions, like holes, are at their MMC when they are at their
__________ of their tolerance zone? - ANSWER ✓ Lower limit
What tolerance condition is the smallest amount of material in a part? - ANSWER
✓ LMC
What is the difference between allowance and clearance? - ANSWER ✓
Allowance is the tightest possible fit, while clearance is the loosest possible fit.
Using datums helps eliminate __________. - ANSWER ✓ Errors in measurement
What is the difference between local and general notes on a blueprint? -
ANSWER ✓ Local notes apply to specific items or areas, while general notes
apply to the entire drawing
What type of drawing defines how the product is going to be manufactured? -
ANSWER ✓ Process drawing
, How is a half scale drawing written? - ANSWER ✓ 1:2
Which of the following lists the proper digital caliper calibration steps in order? -
ANSWER ✓ Turn on the caliper display, close the jaws, press the zero button
Why are dial calipers the most widely used precision measuring instrument on the
shop floor? - ANSWER ✓ They are easy to carry
They take measurements quickly
They are reasonably accurate
How often should a micrometer's calibration be checked? - ANSWER ✓ Every
few months
Which of the following items can affect a micrometer's measurement? - ANSWER
✓ Dust
Oil
Shavings
Burrs
Force is any attempt to change the motion of an object and is measured in
__________. - ANSWER ✓ Newtons (N) and pound-force (lbf)
Potential energy is stored energy until it is allowed to move, then it becomes
__________. - ANSWER ✓ Kinetic energy
Mass is the amount of __________ the object contains. - ANSWER ✓ Matter
Air supplied to a pneumatic system is supplied through the __________ line. -
ANSWER ✓ Supply
A(n) __________ provides power to a hydraulic system by pumping oil from a
reservoir into the supply lines.. - ANSWER ✓ Pump
What can compressed air that is less than 30 psi be used for? - ANSWER ✓
Cleaning work areas
