Alberta welding first year final AIT COMPLETE EXAM
LATEST VERSION 2026-2027 QUESTIONS AND 100%
Verified ANSWERS
What is the total number of hours in the first period Welder Training
Profile? - answer>>>240
When starting a cut on plate, the preheat cones should be held: -
answer>>>about 3 mm (1/8") above the surface.
What is the main purpose of the contact tube? - answer>>>transfers
the welding current to the filler wire
A steamed vessel is safest to weld on when it is cooled down to room
temperature . - answer>>>False
Three basic oxy/acetylene flame types are known as: -
answer>>>carbonizing, neutral, oxidizing
Which of the following is a abbreviation of a welding process? -
answer>>>OAW
What current and polarity is used in plasma Arc cutting and gouging
operations? - answer>>>DCEN and DCRP
"Nesting" in GMAW wire feeder can be caused by: - answer>>>drive
roll pressure is set to high
In the AWS designation ER70T-6, the digit '0' would tell you that: -
answer>>>This is a flat and horizontal filler metal
Grossly unequal pressure of gases may cause a: - answer>>>flashback.
, Alberta welding first year final AIT COMPLETE EXAM
LATEST VERSION 2026-2027 QUESTIONS AND 100%
Verified ANSWERS
-
What is the definition of sling angle? - answer>>>the angle formed by
the legs to the horizontal plane
Where the rigging was assembled or fabricated by the employer, what
percent of the ultimate breaking strength of the weakest component
must the working load not exceed if the rigging is used to support
workers? - answer>>>10%
How much electrode stickout is recommended when using gas
shielded FCAW with 1.2 mm (0.045") wire? - answer>>>10 mm to 19
mm (3/8" to 3/4")
What type of wire feed set-up is used with CV power sources? -
answer>>>constant speed
What would the recommended regulator pressure be if we were to safely
balance a No. 3 welding tip? - answer>>>3 lbs. oxygen and 3 lbs.
acetylene
Excessive penetration on a root pass would likely be caused by: -
answer>>>travel speeds too low.
The amount of oxygen and acetylene, from cylinders, required to form
a neutral cone is: - answer>>>one part oxygen, one part acetylene.
In the GMAW short-circuiting transfer mode, metal is transferred: -
answer>>>when the electrode comes in contact with the weld pool.
When properly applying wire rope clips, the strength of the wire rope is
LATEST VERSION 2026-2027 QUESTIONS AND 100%
Verified ANSWERS
What is the total number of hours in the first period Welder Training
Profile? - answer>>>240
When starting a cut on plate, the preheat cones should be held: -
answer>>>about 3 mm (1/8") above the surface.
What is the main purpose of the contact tube? - answer>>>transfers
the welding current to the filler wire
A steamed vessel is safest to weld on when it is cooled down to room
temperature . - answer>>>False
Three basic oxy/acetylene flame types are known as: -
answer>>>carbonizing, neutral, oxidizing
Which of the following is a abbreviation of a welding process? -
answer>>>OAW
What current and polarity is used in plasma Arc cutting and gouging
operations? - answer>>>DCEN and DCRP
"Nesting" in GMAW wire feeder can be caused by: - answer>>>drive
roll pressure is set to high
In the AWS designation ER70T-6, the digit '0' would tell you that: -
answer>>>This is a flat and horizontal filler metal
Grossly unequal pressure of gases may cause a: - answer>>>flashback.
, Alberta welding first year final AIT COMPLETE EXAM
LATEST VERSION 2026-2027 QUESTIONS AND 100%
Verified ANSWERS
-
What is the definition of sling angle? - answer>>>the angle formed by
the legs to the horizontal plane
Where the rigging was assembled or fabricated by the employer, what
percent of the ultimate breaking strength of the weakest component
must the working load not exceed if the rigging is used to support
workers? - answer>>>10%
How much electrode stickout is recommended when using gas
shielded FCAW with 1.2 mm (0.045") wire? - answer>>>10 mm to 19
mm (3/8" to 3/4")
What type of wire feed set-up is used with CV power sources? -
answer>>>constant speed
What would the recommended regulator pressure be if we were to safely
balance a No. 3 welding tip? - answer>>>3 lbs. oxygen and 3 lbs.
acetylene
Excessive penetration on a root pass would likely be caused by: -
answer>>>travel speeds too low.
The amount of oxygen and acetylene, from cylinders, required to form
a neutral cone is: - answer>>>one part oxygen, one part acetylene.
In the GMAW short-circuiting transfer mode, metal is transferred: -
answer>>>when the electrode comes in contact with the weld pool.
When properly applying wire rope clips, the strength of the wire rope is
