1|Page
ASE Brakes A5 Test ( Exam 1), ASE A5 Brakes, ASE
Brakes A5 ( Exam 3), ASE Brakes A5 Test ( Exam 2)
||Verified Exam!!|| Most Recent Exam Actual Complete
Real Exam Questions And Correct Answers (Verified
Answers) Already Graded A+ || Newest Exam!!
A vehicle equipped with a "hill holding" option has an ABS
code. Which tool would most likely be used to check the
wheel speed sensor?
a. AC volt meter
b. Ohm meter
c. Scan tool
d. Ammeter - Answer-C : scan tool
why : a scan tool or oscilloscope can be used to test a
signal from a digital when speed sensor
The brake system has a soft, sinking pedal with the engine
running. The brake fluid level is at the correct height.
Which of the following could be the cause?
,2|Page
a. a restricted vacuum hose
b. a leaking master cylinder
c. a bypassing master cylinder
d. a stuck open vacuum check valve - Answer-C : a
bypassing master cylinder
why : a bypassing master cylinder would cause a low
pedal and would not cause a loss of fluid
Technician A says the pins should be driven in with a brass
hammer. Technician B says the pins should be lubricated
with brake fluid. Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A OR B - Answer-D : neither A OR B
why : neither technician is correct. this style of pin should
be installed with a torx or hex head socket
,3|Page
Technician A says a hydro-boost system can use the
power steering pump to operate the booster. Technician B
says a hydro-boost system can use engine vacuum to
operate the booster. Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A & B - Answer-A : only A
why : only tech A is correct. a hydro-boost system uses
hydraulic pressure to create boost
A disc brake caliper is dragging. All of the following could
be the cause EXCEPT
a. binding pins
b. sticking piston
c. binding caliper
d. worn brake pads - Answer-D : worn brake pads
, 4|Page
why : worn brake pads will not cause the brakes to drag
A drum is chattering on the brake lathe. This could be a
result of
a. failure to install the dampening belt
b. cutting too slowly
c. dull cutting blades
d. cutting speed too fast - Answer-A : failure to install the
dampening belt
why : a missing dampening belt could cause the drum to
vibrate while on the lathe. this vibration can cause the
drum to bounce on the cutting tip and make a chattering
noise
A vehicle equipped with a hydro-boost brake system has a
hard pedal with little braking action. Which of the following
could be the cause?
a. low brake fluid
b. air in the brake fluid
c. low power steering fluid
ASE Brakes A5 Test ( Exam 1), ASE A5 Brakes, ASE
Brakes A5 ( Exam 3), ASE Brakes A5 Test ( Exam 2)
||Verified Exam!!|| Most Recent Exam Actual Complete
Real Exam Questions And Correct Answers (Verified
Answers) Already Graded A+ || Newest Exam!!
A vehicle equipped with a "hill holding" option has an ABS
code. Which tool would most likely be used to check the
wheel speed sensor?
a. AC volt meter
b. Ohm meter
c. Scan tool
d. Ammeter - Answer-C : scan tool
why : a scan tool or oscilloscope can be used to test a
signal from a digital when speed sensor
The brake system has a soft, sinking pedal with the engine
running. The brake fluid level is at the correct height.
Which of the following could be the cause?
,2|Page
a. a restricted vacuum hose
b. a leaking master cylinder
c. a bypassing master cylinder
d. a stuck open vacuum check valve - Answer-C : a
bypassing master cylinder
why : a bypassing master cylinder would cause a low
pedal and would not cause a loss of fluid
Technician A says the pins should be driven in with a brass
hammer. Technician B says the pins should be lubricated
with brake fluid. Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A OR B - Answer-D : neither A OR B
why : neither technician is correct. this style of pin should
be installed with a torx or hex head socket
,3|Page
Technician A says a hydro-boost system can use the
power steering pump to operate the booster. Technician B
says a hydro-boost system can use engine vacuum to
operate the booster. Who is correct? ( pg. 47 )
a. A
b. B
c. A & B
d. neither A & B - Answer-A : only A
why : only tech A is correct. a hydro-boost system uses
hydraulic pressure to create boost
A disc brake caliper is dragging. All of the following could
be the cause EXCEPT
a. binding pins
b. sticking piston
c. binding caliper
d. worn brake pads - Answer-D : worn brake pads
, 4|Page
why : worn brake pads will not cause the brakes to drag
A drum is chattering on the brake lathe. This could be a
result of
a. failure to install the dampening belt
b. cutting too slowly
c. dull cutting blades
d. cutting speed too fast - Answer-A : failure to install the
dampening belt
why : a missing dampening belt could cause the drum to
vibrate while on the lathe. this vibration can cause the
drum to bounce on the cutting tip and make a chattering
noise
A vehicle equipped with a hydro-boost brake system has a
hard pedal with little braking action. Which of the following
could be the cause?
a. low brake fluid
b. air in the brake fluid
c. low power steering fluid
