1|Page
Michigan State Brakes Certification Actual Verified
Exam And Practice Newest With Complete Questions
And Correct Detailed Answers|| Newest Exam!!!
A cracked or torn vacuum diaphragm in a brake power
booster would most likely cause: - Answer-a hard pedal
feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums
on a rear wheel drive vehicle. What is the most likely
cause of this problem? - Answer-A plugged axle
Which of the following incorrect service procedures will
cause brake lock-up? - Answer-master cylinder push rod
adjusted too long
Which of the following describes the proper way to
depressurized an ABS system? - Answer-Pump the brake
pedal at least 25 times (or more, depending on the
manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings
installed and the drums machined. the most likely cause is
,2|Page
the: - Answer-technician use the parking brake to adjust
shoes and the cable is stuck
When turning brake drums: - Answer-use a dampening
strap to reduce chatter
Most 1995 & newer vehicles use which of the following
types of wheels bearings on non-drive wheel? - Answer-
Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you
should pump the brake pedal at least 4 times, hold the
brake pedal depressed, and start the engine. the brake
pedal should: - Answer-drop slightly and remain firm
You are installing a set of brake shoe linings that are not
the same length. Traditionally, the primary shoe lining is: -
Answer-Smaller and goes towards the front of the car.
Which of the following is NOT a necessary drum brake
measurement? - Answer-run-out
, 3|Page
On a 3-channel system, which wheels are on the same
circuit? - Answer-both rear wheels
One way to test an ABS wheel speed signal is to use
_____ on your digital multimeter. - Answer-AC volts
The key input for the ABS control module comes from the:
- Answer-wheel speed sensors
ABS speed sensor and sensor rings: - Answer-should not
be hammered or tapped on and should always be
replaced as a matched set
Flexible brake hoses should be replaced: - Answer-when
dampness is evident on the hose
Which of the following should be used to check for rotor
thickness variation: - Answer-Micrometer
After rebuilding a master cylinder, the rod between the
master cylinder and booster should be: - Answer-adjusted
properly
Michigan State Brakes Certification Actual Verified
Exam And Practice Newest With Complete Questions
And Correct Detailed Answers|| Newest Exam!!!
A cracked or torn vacuum diaphragm in a brake power
booster would most likely cause: - Answer-a hard pedal
feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums
on a rear wheel drive vehicle. What is the most likely
cause of this problem? - Answer-A plugged axle
Which of the following incorrect service procedures will
cause brake lock-up? - Answer-master cylinder push rod
adjusted too long
Which of the following describes the proper way to
depressurized an ABS system? - Answer-Pump the brake
pedal at least 25 times (or more, depending on the
manufacturer's recommendation) with the ignition off.
The rear brakes are dragging after having new linings
installed and the drums machined. the most likely cause is
,2|Page
the: - Answer-technician use the parking brake to adjust
shoes and the cable is stuck
When turning brake drums: - Answer-use a dampening
strap to reduce chatter
Most 1995 & newer vehicles use which of the following
types of wheels bearings on non-drive wheel? - Answer-
Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you
should pump the brake pedal at least 4 times, hold the
brake pedal depressed, and start the engine. the brake
pedal should: - Answer-drop slightly and remain firm
You are installing a set of brake shoe linings that are not
the same length. Traditionally, the primary shoe lining is: -
Answer-Smaller and goes towards the front of the car.
Which of the following is NOT a necessary drum brake
measurement? - Answer-run-out
, 3|Page
On a 3-channel system, which wheels are on the same
circuit? - Answer-both rear wheels
One way to test an ABS wheel speed signal is to use
_____ on your digital multimeter. - Answer-AC volts
The key input for the ABS control module comes from the:
- Answer-wheel speed sensors
ABS speed sensor and sensor rings: - Answer-should not
be hammered or tapped on and should always be
replaced as a matched set
Flexible brake hoses should be replaced: - Answer-when
dampness is evident on the hose
Which of the following should be used to check for rotor
thickness variation: - Answer-Micrometer
After rebuilding a master cylinder, the rod between the
master cylinder and booster should be: - Answer-adjusted
properly
