1|Page
RAMSAY MAINTENANCE EXAM LATEST 2026-2027 ACTUAL EXAM
WITH COMPLETE QUESTIONS AND CORRECT DETAILED ANSWERS
(100% VERIFIED ANSWERS) |ALREADY GRADED A+| ||PROFESSOR
VERIFIED|| ||BRANDNEW!!!||
Which of the following can transfer power between two turning
shafts located at right angles?
A. Spur gears
B. Worm gears
C. Rack and pinion gears
D. Herringbone gears - ANSWER-B. Worm gears
The best way to keep dirt out of a bearing is to use
A. a seal.
B. a cap.
C. a shield.
D. packing. - ANSWER-A. a seal.
An overload on a torque limiter will most likely cause
A. the motor to kick out.
,2|Page
B. a bent shaft.
C. increased motor torque.
D. slippage. - ANSWER-D. slippage.
When a shaft mounted on two bearings must be positioned
axially,
A. one bearing should be fixed and the other floating.
B. both bearings must be fixed.
C. a thrust bearing must be added to this shaft.
D. both bearings should be floating. - ANSWER-A. one bearing
should be fixed and the other floating.
Clutches on machinery provide for disengaging and sometimes
allow for
A. positive drive.
B. misalignment.
C. slippage.
D. variable speed. - ANSWER-A. positive drive.
,3|Page
Fluid clutches are used on equipment that is subjected to
A. shock loading.
B. misalignment.
C. frequent stopping.
D. continuous running. - ANSWER-D. continuous running.
Selection of gear reducer size is determined by
A. Output shaft diameter
B. Lubrication capacity
C. Horsepower rating and gear ratio
D. environment in which it will be used - ANSWER-C. Horsepower
rating and gear ratio
An EP grease would be best suited for which of the flowing?
A. High speed, low pressure
B. High speed, low temperature
C. Low speed, low pressure
D. Low speed, high pressure - ANSWER-D. Low speed, high
pressure
, 4|Page
The viscosity of an oil is affected most by
A. contamination.
B. resistance to corrosion.
C. pressure.
D. temperature. - ANSWER-D. temperature.
Good lubricating oil must
A. Be moist and toxic
B. Prevents rust and corrosion
C. Be clear in color
D. Be readily water soluble - ANSWER-B. Prevents rust and
corrosion
What is the most important quality of oil film lubrication?
A. Separates moving surfaces - ANSWER-A. Separates moving
surfaces
A gear pump positive displacement pump is also known as a
RAMSAY MAINTENANCE EXAM LATEST 2026-2027 ACTUAL EXAM
WITH COMPLETE QUESTIONS AND CORRECT DETAILED ANSWERS
(100% VERIFIED ANSWERS) |ALREADY GRADED A+| ||PROFESSOR
VERIFIED|| ||BRANDNEW!!!||
Which of the following can transfer power between two turning
shafts located at right angles?
A. Spur gears
B. Worm gears
C. Rack and pinion gears
D. Herringbone gears - ANSWER-B. Worm gears
The best way to keep dirt out of a bearing is to use
A. a seal.
B. a cap.
C. a shield.
D. packing. - ANSWER-A. a seal.
An overload on a torque limiter will most likely cause
A. the motor to kick out.
,2|Page
B. a bent shaft.
C. increased motor torque.
D. slippage. - ANSWER-D. slippage.
When a shaft mounted on two bearings must be positioned
axially,
A. one bearing should be fixed and the other floating.
B. both bearings must be fixed.
C. a thrust bearing must be added to this shaft.
D. both bearings should be floating. - ANSWER-A. one bearing
should be fixed and the other floating.
Clutches on machinery provide for disengaging and sometimes
allow for
A. positive drive.
B. misalignment.
C. slippage.
D. variable speed. - ANSWER-A. positive drive.
,3|Page
Fluid clutches are used on equipment that is subjected to
A. shock loading.
B. misalignment.
C. frequent stopping.
D. continuous running. - ANSWER-D. continuous running.
Selection of gear reducer size is determined by
A. Output shaft diameter
B. Lubrication capacity
C. Horsepower rating and gear ratio
D. environment in which it will be used - ANSWER-C. Horsepower
rating and gear ratio
An EP grease would be best suited for which of the flowing?
A. High speed, low pressure
B. High speed, low temperature
C. Low speed, low pressure
D. Low speed, high pressure - ANSWER-D. Low speed, high
pressure
, 4|Page
The viscosity of an oil is affected most by
A. contamination.
B. resistance to corrosion.
C. pressure.
D. temperature. - ANSWER-D. temperature.
Good lubricating oil must
A. Be moist and toxic
B. Prevents rust and corrosion
C. Be clear in color
D. Be readily water soluble - ANSWER-B. Prevents rust and
corrosion
What is the most important quality of oil film lubrication?
A. Separates moving surfaces - ANSWER-A. Separates moving
surfaces
A gear pump positive displacement pump is also known as a
