BICSI Technician Exam with verified detailed solutions || || || || || ||
What network topology connects each device on the network to its neighbor device until all
|| || || || || || || || || || || || || || ||
devices are connected - ✔✔Hybird || || || ||
When expanding an existing TR where the wall needs to be removed and has active
|| || || || || || || || || || || || || || ||
equipment and terminations attached the installer will need to - ✔✔Float the wall or rack
|| || || || || || || || || || || || || ||
What common cabinet configuration providing increased efficiency in heat management is
|| || || || || || || || || || ||
where - ✔✔The hot side of two cabinet rows face each other
|| || || || || || || || || || ||
What are pulling sheafed used for? - ✔✔To assist in the routing of the cable to the point
|| || || || || || || || || || || || || || || || || ||
where it will be pulled to the upper floors
|| || || || || || || ||
What are the 2 types of EMT couplings used to connect sections together? - ✔✔Compression
|| || || || || || || || || || || || || || ||
and set screws || ||
Using company property for business only, being punctual and maintaining confidentiality
|| || || || || || || || || || ||
are examples of____________ - ✔✔Professionalism
|| || || ||
Radiating cable standoffs supports should be installed a MINIMUM of ____________ below
|| || || || || || || || || || || ||
the cable tray - ✔✔77mm (3in)
|| || || || ||
If you are connecting a pul rope to optical fiber without a wire mesh or pulling eye what
|| || || || || || || || || || || || || || || || || ||
should you connect to - ✔✔The aramid yarn
|| || || || || || ||
To avoid electromagnetic interference in cabling what is the recommended minimum
|| || || || || || || || || || ||
separation from fluorescent lamps - ✔✔150 mm ( 6in) || || || || || || || ||
What network topology connects each device on the network to its neighbor device until all
|| || || || || || || || || || || || || || ||
devices are connected - ✔✔Hybird || || || ||
When expanding an existing TR where the wall needs to be removed and has active
|| || || || || || || || || || || || || || ||
equipment and terminations attached the installer will need to - ✔✔Float the wall or rack
|| || || || || || || || || || || || || ||
What common cabinet configuration providing increased efficiency in heat management is
|| || || || || || || || || || ||
where - ✔✔The hot side of two cabinet rows face each other
|| || || || || || || || || || ||
What are pulling sheafed used for? - ✔✔To assist in the routing of the cable to the point
|| || || || || || || || || || || || || || || || || ||
where it will be pulled to the upper floors
|| || || || || || || ||
What are the 2 types of EMT couplings used to connect sections together? - ✔✔Compression
|| || || || || || || || || || || || || || ||
and set screws || ||
Using company property for business only, being punctual and maintaining confidentiality
|| || || || || || || || || || ||
are examples of____________ - ✔✔Professionalism
|| || || ||
Radiating cable standoffs supports should be installed a MINIMUM of ____________ below
|| || || || || || || || || || || ||
the cable tray - ✔✔77mm (3in)
|| || || || ||
If you are connecting a pul rope to optical fiber without a wire mesh or pulling eye what
|| || || || || || || || || || || || || || || || || ||
should you connect to - ✔✔The aramid yarn
|| || || || || || ||
To avoid electromagnetic interference in cabling what is the recommended minimum
|| || || || || || || || || || ||
separation from fluorescent lamps - ✔✔150 mm ( 6in) || || || || || || || ||
