FDOT Final Estimates Level 1 EXAM PREP 2026/2027 COMPLETE QUESTIONS AND CORRECT DETAILED ANSWERS || 100% GUARANTEED PASS RECENT VERSION

FDOT Final Estimates Level 1 EXAM PREP 2026/2027 COMPLETE QUESTIONS AND CORRECT DETAILED ANSWERS || 100% GUARANTEED PASS RECENT VERSION 1. Which of the items listed below is NOT included in the Final Estimates package? - ANSWER Density log books 2. What is placed on the plan sheets to call particular attention to unusual conditions? - ANSWER Plan Notes 3. What would you use to document field changes in the plans? - ANSWER Black ball point pen & Black pencil 4. What is the basis for payment of final quantities? - ANSWER Site Source records 5. What software is available for calculation final pa quantities? - ANSWER Engineering Menu 6. According to the standard weight table, what is the TOTAL weight of the following quantities of bolts? - ANSWER 1,472 Ibs 7. Which of the following documents are used for reviewing contract time charges before clearing estimates for final payment? - ANSWER Construction Diaries 8. It is usually necessary to measure items, which are to be paid for on a lump sum or "plan quantity" basis. - ANSWER FALSE 9. On the transmittal letter, how should field books be listed? - ANSWER Book number & description of contents 10. What is the rea of the sodded section shown below? - ANSWER 11,241 SY 11. When a pay item is based on truck capacity and side boards have been added to the truck body, what should you submit with the final estimates package? - ANSWER Sketches of truck measurements 12. Examples of site source records include: - ANSWER Field books, tally sheets asphalt reports, latitude & department 13. While on aa metric project, what method would be used to document final measured items in the field for site source record documentation. - ANSWER Use only metric measuring devices, no conversion is allowed 14. What two types of Estimates are needed to pay for the work performed by contractors? - ANSWER Final & Progress Monthly 15. In case of discrepancies among the contract documents, which document takes the highest precedence? - ANSWER Special Provisions 16. Contractors Recieve progress payments on the basis of? - ANSWER Monthly Progress Estimates 17. Which of the following sets forth the Department's methods and procedures for preparing and checking final estimates? - ANSWER Preparation and Documentation Manual (PDM) 18. Which Document contains a series of Specially designed forms that show both original estimates of quantities and the final quantities as measured ad accepted? - ANSWER Computation Books 19. Which Document contains alignment notes, cross-section notes, linear and area measurements and dimension sketches? - ANSWER Field Notebooks 20. Where are major changes during construction documented and "as-built" conditions shown? - ANSWER Field Notebooks 21. What identification is needed to show on the front cover of a field book? - ANSWER FEID, Contract number, General contents of the book 22. When making corrections to a field book entry, you should: - ANSWER strike through, initial and enter correct data and date 23. What should be started on the first lined page (page 1) of a field book? - ANSWER INDEX 24. An entire page of a field notebook you are using is incorrect, what do you do to correct the situation? - ANSWER Mark the page VOID and reference it to a new page showing the correct information. 25. "Check Levels" must be run at the start of a construction project to assure that: - ANSWER Construction will be done to design elevations & final measurements for payment will be from the same base elevations as the original survey. 26. Most Linear pay items are measures in linear ________? - ANSWER Feet 27. Aside from measuring the length of fence, you should count and document the number of: - ANSWER Corner post assemblies & pull and end post assemblies 28. The various fencing post assemblies are identified by approximate ________ and are totaled in a ___________. - ANSWER Station; field notbook 29. You should be sure that the batch scales nd automatic printer at an asphalt plant are certified for accuracy every __________. - ANSWER Six Months 30. The accuracy of batch scales and automatic printers should be checked: - ANSWER At least once a week & before accepting the first load on a project. 31. Documentation of "per each" items is usually in the form of a tabulation by _________________________. - ANSWER Location 32. Which of the Following are NOT often paid for on a lump sum basis? - ANSWER Box Culverts 33. On a certain project, the contractor's lump sum bid for clearing and grubbing was based on the expectation of clearing 12.380 acres at a unit price of $20,000. During the project FDOT decided to reduce the original acreage to be cleared and grubbed by (2.105 acres). What should the lump sum quantity be adjusted to? - ANSWER 0.83 LS