ABYC Systems ACTUAL EXAM QUESTIONS
WITH COMPLETE SOLUTION GUIDE) (MULTIPLE
CHOICES) (A+ GRADED 100% VERIFIED) LATEST
VERSION 2026
Save
Terms in this set (151)
Ball valves may be sealed to E
through hull fittings with:
A. 5200
B. SikaFlex
C. Teflon
D. All the above
E. None of the above
Tubes are measured by: B
A. ID
B. OD
C. nominal size
pipes may not be connected by: C
A. Welding
B. Threaded fittings
C. Compression fittings
D. Glue
,Tech A says Seacocks must be C
readily accessible. Tech B say its ok
to have them within 12" of the
engine. who is correct?
A. Tech A
B. Tech B
C. Both
D. neither
Tech A says that it is all right to D
connect an auxiliary line to the
potable water pump as long as
there is a siphon break. Technician B
says you must have a lockable Y
valve to prevent cross
contamination. who is right?
A. Tech A
B. Tech B
C. Both
D. Neither
A bildge pump discharge line must D
be:
A. equipped with a check valve to
prevent back flow and nuisance
cycling
B. Equipped with a properly
installed seacock
C. No more than 30' long
D. non of the above
, ball valves below the waterline D
must be:
A. ABYC approved
B. ABYC Certified
C. ABYC endorsed
D. none of the above
potable water systems must D
discharge
A. into a sump
B. Overboard
C. Into the grey water tank
D. any of the above
Tubes are measured in _________ and OD ID
hoses are measured in _________
Which of the following components A
may need to be by-passed for the
purpose of decommissioning?
A. Tanks, filters and water heaters
B. Strainers, tanks and pumps
C. Fixtures and lines
D. Dockside water connections
Which of the following agencies B
must be referenced when selecting
materials for use in a portable water
system?
A. DOT
B. FDA
C. USCG
D. UL
WITH COMPLETE SOLUTION GUIDE) (MULTIPLE
CHOICES) (A+ GRADED 100% VERIFIED) LATEST
VERSION 2026
Save
Terms in this set (151)
Ball valves may be sealed to E
through hull fittings with:
A. 5200
B. SikaFlex
C. Teflon
D. All the above
E. None of the above
Tubes are measured by: B
A. ID
B. OD
C. nominal size
pipes may not be connected by: C
A. Welding
B. Threaded fittings
C. Compression fittings
D. Glue
,Tech A says Seacocks must be C
readily accessible. Tech B say its ok
to have them within 12" of the
engine. who is correct?
A. Tech A
B. Tech B
C. Both
D. neither
Tech A says that it is all right to D
connect an auxiliary line to the
potable water pump as long as
there is a siphon break. Technician B
says you must have a lockable Y
valve to prevent cross
contamination. who is right?
A. Tech A
B. Tech B
C. Both
D. Neither
A bildge pump discharge line must D
be:
A. equipped with a check valve to
prevent back flow and nuisance
cycling
B. Equipped with a properly
installed seacock
C. No more than 30' long
D. non of the above
, ball valves below the waterline D
must be:
A. ABYC approved
B. ABYC Certified
C. ABYC endorsed
D. none of the above
potable water systems must D
discharge
A. into a sump
B. Overboard
C. Into the grey water tank
D. any of the above
Tubes are measured in _________ and OD ID
hoses are measured in _________
Which of the following components A
may need to be by-passed for the
purpose of decommissioning?
A. Tanks, filters and water heaters
B. Strainers, tanks and pumps
C. Fixtures and lines
D. Dockside water connections
Which of the following agencies B
must be referenced when selecting
materials for use in a portable water
system?
A. DOT
B. FDA
C. USCG
D. UL
