Maine State Journeyman Exam up to
15gph Questions With Verified
Answers
\.How many apprentices can a journeyman directly supervise? - ANSWERS✔-2
\.When performing any service work on a customers heating system the licensee
must notify the homeowner of? - ANSWERS✔-Efficiency and code violations
\.Can a licensed journeyman perform a cleaning on wood/oil combination unit
without direct supervision? - ANSWERS✔-No
\.When installing a furnace, direct wired water heater or boiler what must be
done prior to placing it in service? - ANSWERS✔-Everything complies with NFPA
31 code
\.When installing a new oil burner the _______ must be brought into compliance
with the rules of the board before ______? - ANSWERS✔-Wiring Start up
\.When an emergency situation arises that does not allow adequate time to get
the chimney lined/repaired before installing the new heating appliance what can
be done? - ANSWERS✔-90 day waiver
, \.Who is responsible for ensuring repairs or the chimney is lined within the 90
days? - ANSWERS✔-Installer\Licensee
\.When is a heat loss required? - ANSWERS✔-For new install
\.Prior to a boiler replacement a________ or a ________ Must be conducted
before replacement of an existing system. - ANSWERS✔-Heat loss/ heat load
\.The low-water cut off must be located where? - ANSWERS✔-6 inches above
boiler crown sheet but in no case below
\.An oil supply or return line under cement subfloor or earth must be ________
And without ________? - ANSWERS✔-Sleeved Fittings (continuous)
\.Coated copper tubing must have _______ Installed at the tank when ________?
- ANSWERS✔-OSV Underground
\.Whenever an outlet of an oil supply tank is located more than ______ above the
burner a _____ or _____ valve is required. - ANSWERS✔-4ft OSV or PRV
\.Unprotected lines that are buried or grouted must be? - ANSWERS✔-removed
from service
\.All fuel supply tanks must be a minimum of _____ From any gas and or solid fuel
burning appliance - ANSWERS✔-5ft
15gph Questions With Verified
Answers
\.How many apprentices can a journeyman directly supervise? - ANSWERS✔-2
\.When performing any service work on a customers heating system the licensee
must notify the homeowner of? - ANSWERS✔-Efficiency and code violations
\.Can a licensed journeyman perform a cleaning on wood/oil combination unit
without direct supervision? - ANSWERS✔-No
\.When installing a furnace, direct wired water heater or boiler what must be
done prior to placing it in service? - ANSWERS✔-Everything complies with NFPA
31 code
\.When installing a new oil burner the _______ must be brought into compliance
with the rules of the board before ______? - ANSWERS✔-Wiring Start up
\.When an emergency situation arises that does not allow adequate time to get
the chimney lined/repaired before installing the new heating appliance what can
be done? - ANSWERS✔-90 day waiver
, \.Who is responsible for ensuring repairs or the chimney is lined within the 90
days? - ANSWERS✔-Installer\Licensee
\.When is a heat loss required? - ANSWERS✔-For new install
\.Prior to a boiler replacement a________ or a ________ Must be conducted
before replacement of an existing system. - ANSWERS✔-Heat loss/ heat load
\.The low-water cut off must be located where? - ANSWERS✔-6 inches above
boiler crown sheet but in no case below
\.An oil supply or return line under cement subfloor or earth must be ________
And without ________? - ANSWERS✔-Sleeved Fittings (continuous)
\.Coated copper tubing must have _______ Installed at the tank when ________?
- ANSWERS✔-OSV Underground
\.Whenever an outlet of an oil supply tank is located more than ______ above the
burner a _____ or _____ valve is required. - ANSWERS✔-4ft OSV or PRV
\.Unprotected lines that are buried or grouted must be? - ANSWERS✔-removed
from service
\.All fuel supply tanks must be a minimum of _____ From any gas and or solid fuel
burning appliance - ANSWERS✔-5ft
