A-levelDESIGN AND TECHNOLOGY:
PRODUCT DESIGN 7552/2 ACTUAL 2025
PAPER MERGED WITH MARK SCHEME
vincent marekia
[COMPANY NAME] [Company address]
, 1
Do not write
outside the
box
Please write clearly in block capitals.
Centre number
Surname _________________________________________________________________________
Forename(s) _________________________________________________________________________
Candidate signature _________________________________________________________________________
I declare this is my own work.
A-level
For Examiner’s Use
Question Mark
Candid 1
ate
number 2–3
DESIGN AND TECHNOLOGY: PRODUCT DESIGN 4
7552/2 5
ACTUAL 2025 PAPER 6
MERGED WITH MARK 7–8
SCHEME 9–11
Paper 2 Designing and Making Principles 12
13
14
15
TOTAL
Tuesday 10 June 2025 Morning Time allowed: 1 hour 30 minutes
Materials
For this paper you must have:
lnormal writing and drawing instruments l a scientific calculator.
Instructions l Use black ink or black ball-point pen. Use pencil only for drawing. l Fill in the boxes at
the top of this page. l Answer all questions. l You must answer the questions in the spaces provided.
Do not write outside the box around each page or on blank pages. l If you need extra space for your
G/Jun25/7552/2
, 2
Do not write
outside the
box
answer(s), use the lined pages at the end of this book. Write the question number against your
answer(s). l Do all rough work in this book. Cross through any work you do not want to be marked.
Information l The marks for questions are shown in brackets. l The maximum mark for this paper is
80. l There are 30 marks for Section A and 50 marks for Section B.
(JUN257552201) G/KL/Jun25/G4006/V5 7552/2
Section A – Product Analysis
Answer all questions in this section.
Turn over U
G/Jun25/7552/2
, 3
Do not write
outside the
box
0 1
Figures 1 and 2 show two pens.
Figure 1 Disposable Figure 2
polymer pen Refillable stainless steel pen
Figure 1 Figure 2
Material(s) used Thermoplastics Stainless Steel
Manufacturing processes used Polymer deformation Metal deformation
Compare and evaluate the two pens shown.
In your answer you should refer to material and design suitability for large-scale
production.
[12 marks]
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
(02)
G/Jun25/7552/2
PRODUCT DESIGN 7552/2 ACTUAL 2025
PAPER MERGED WITH MARK SCHEME
vincent marekia
[COMPANY NAME] [Company address]
, 1
Do not write
outside the
box
Please write clearly in block capitals.
Centre number
Surname _________________________________________________________________________
Forename(s) _________________________________________________________________________
Candidate signature _________________________________________________________________________
I declare this is my own work.
A-level
For Examiner’s Use
Question Mark
Candid 1
ate
number 2–3
DESIGN AND TECHNOLOGY: PRODUCT DESIGN 4
7552/2 5
ACTUAL 2025 PAPER 6
MERGED WITH MARK 7–8
SCHEME 9–11
Paper 2 Designing and Making Principles 12
13
14
15
TOTAL
Tuesday 10 June 2025 Morning Time allowed: 1 hour 30 minutes
Materials
For this paper you must have:
lnormal writing and drawing instruments l a scientific calculator.
Instructions l Use black ink or black ball-point pen. Use pencil only for drawing. l Fill in the boxes at
the top of this page. l Answer all questions. l You must answer the questions in the spaces provided.
Do not write outside the box around each page or on blank pages. l If you need extra space for your
G/Jun25/7552/2
, 2
Do not write
outside the
box
answer(s), use the lined pages at the end of this book. Write the question number against your
answer(s). l Do all rough work in this book. Cross through any work you do not want to be marked.
Information l The marks for questions are shown in brackets. l The maximum mark for this paper is
80. l There are 30 marks for Section A and 50 marks for Section B.
(JUN257552201) G/KL/Jun25/G4006/V5 7552/2
Section A – Product Analysis
Answer all questions in this section.
Turn over U
G/Jun25/7552/2
, 3
Do not write
outside the
box
0 1
Figures 1 and 2 show two pens.
Figure 1 Disposable Figure 2
polymer pen Refillable stainless steel pen
Figure 1 Figure 2
Material(s) used Thermoplastics Stainless Steel
Manufacturing processes used Polymer deformation Metal deformation
Compare and evaluate the two pens shown.
In your answer you should refer to material and design suitability for large-scale
production.
[12 marks]
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
___________________________________________________________________________________
(02)
G/Jun25/7552/2
