3/19/26, 4:26 PM Virginia State Inspection Test EXAM, Complete Test || Questions and Answers (Verified Answers) (Latest Update 2026) UPDATE!! …
Virginia State Inspection Test EXAM, Complete
Test || Questions and Answers (Verified Answers)
(Latest Update 2026) UPDATE!! Virginia State
Inspection Assessment Test
Save
Terms in this set (83)
On vehicles like firetrucks,
ambulances, etc. permitted to have
flashing, blinking, or alternating
lights may be equipped with the
means to flash their headlamps when
their emergency warning lamps are
activated but the headlamps are
required to be wired to allow either
the upper or lower beam to flash but
not both.
Motorcycles: Reject if the center of
the hot spot is set more than four
inches up or down from the
horizontal centerline or more than
four inches to the left or right from
the vertical centerline.
https://quizlet.com/1157894668/virginia-state-inspection-test-exam-complete-test-questions-and-answers-verified-answers-latest-update-2026-update… 1/15
, 3/19/26, 4:26 PM Virginia State Inspection Test EXAM, Complete Test || Questions and Answers (Verified Answers) (Latest Update 2026) UPDATE!! …
Reject if a vehicle, trailer, etc that
requires clearance lamps is not
equipped with amber reflectors on
the sides as near the front as
practical, as well as the rear.
Reflectors must be 15 inches and not
more than 60 inches from the
ground. (Reflectors can have cracks,
but cannot have a piece broken from
the surface.
Reject if headlamps are not aimed
within the following tolerances using
the optical aimer:
1. The center of the hot spot of all
single element high beam lamps is
set more than 4 inches up or down
from the horizontal centerline or
more than 4 inches to the left or
right from the vertical centerline.
2. The left edge of the lamp pattern
of any low beam lamp or any
combination or multi-element lamp is
more than 4 inches to the left or
right of the vertical centerline or the
top edge of the lamp pattern is more
than 4 inches above or below the
horizontal centerline when checked
on low beam.
Headlamps: except motorcycles: True
True or false: Rejected if a headlamp
visor is over two inches long unless
part of the original body design.
https://quizlet.com/1157894668/virginia-state-inspection-test-exam-complete-test-questions-and-answers-verified-answers-latest-update-2026-update… 2/15
Virginia State Inspection Test EXAM, Complete
Test || Questions and Answers (Verified Answers)
(Latest Update 2026) UPDATE!! Virginia State
Inspection Assessment Test
Save
Terms in this set (83)
On vehicles like firetrucks,
ambulances, etc. permitted to have
flashing, blinking, or alternating
lights may be equipped with the
means to flash their headlamps when
their emergency warning lamps are
activated but the headlamps are
required to be wired to allow either
the upper or lower beam to flash but
not both.
Motorcycles: Reject if the center of
the hot spot is set more than four
inches up or down from the
horizontal centerline or more than
four inches to the left or right from
the vertical centerline.
https://quizlet.com/1157894668/virginia-state-inspection-test-exam-complete-test-questions-and-answers-verified-answers-latest-update-2026-update… 1/15
, 3/19/26, 4:26 PM Virginia State Inspection Test EXAM, Complete Test || Questions and Answers (Verified Answers) (Latest Update 2026) UPDATE!! …
Reject if a vehicle, trailer, etc that
requires clearance lamps is not
equipped with amber reflectors on
the sides as near the front as
practical, as well as the rear.
Reflectors must be 15 inches and not
more than 60 inches from the
ground. (Reflectors can have cracks,
but cannot have a piece broken from
the surface.
Reject if headlamps are not aimed
within the following tolerances using
the optical aimer:
1. The center of the hot spot of all
single element high beam lamps is
set more than 4 inches up or down
from the horizontal centerline or
more than 4 inches to the left or
right from the vertical centerline.
2. The left edge of the lamp pattern
of any low beam lamp or any
combination or multi-element lamp is
more than 4 inches to the left or
right of the vertical centerline or the
top edge of the lamp pattern is more
than 4 inches above or below the
horizontal centerline when checked
on low beam.
Headlamps: except motorcycles: True
True or false: Rejected if a headlamp
visor is over two inches long unless
part of the original body design.
https://quizlet.com/1157894668/virginia-state-inspection-test-exam-complete-test-questions-and-answers-verified-answers-latest-update-2026-update… 2/15
