Network Security Essentials
For each VLAN interface, what number of untagged networks can you have? *
A) One
B) Four
C) Unlimited
D) Dependent at the firewall model - ANS-A
In order to study the site visitors that passes over you HTTP coverage, what do you need to
make certain to do first? *
A) Turn up Diagnostic Logging underneath the Setup > Logging menu.
B) Turn on logging inside of WebBlocker.
C) No trade wishes to be made. All guidelines log by default.
D) Turn on Logging within the HTTP policy. - ANS-D
True or False: A Feature Key may be migrated among gadgets. *
True
False - ANS-False
A Feature Key is specific to a selected device, due to the fact it's far based at the serial quantity.
True or False: A packet clear out is the maximum stable way to pass traffic thru your firewall. *
True
False - ANS-False.
A packet filter out definitely critiques the header statistics of a packet. A proxy is what allows for
greater in-depth filtering of the site visitors, for that reason presenting extra security.
True or False: APT Blocker requires that Gateway Antivirus be enabled. *
True
False - ANS-True.
APT Blocker uses the equal scanning engine as APT Blocker, so the GAV carrier must first be
enabled.
True or False: In order for a Branch Office VPN to be built the Tunnel have to be installed first. *
True
False - ANS-False.
The Gateway should set up first.
, True or False: In order to allow NAT Loopback on your firewall, you need to configure this under
the Dynamic NAT settings. *
True
False - ANS-False.
NAT Loopback does no longer require whatever to be enabled. You easy must write a coverage
to allow it.
True or False: Policy precedence is most often decided via the alphabetical order of coverage
names. *
True
False - ANS-False.
Policy precedence is determined via how precise the policy is with reference to what visitors is
permitted.
True or False: There are 3 modes you can operate your firewall below: Mixed Routing, Bridged
and Drop-In. Bridged mode is the default choice. *
True
False - ANS-False.
Mixed Routing mode is the default mode.
True or False: Through Firebox System Manager, you may run the TCP Dump command. *
True
False - ANS-True.
This choice is available beneath the Diagnostic Tasks tool.
True or False: When putting in place a static path, a lower metric approach a lower precedence.
*
True
False - ANS-False
A decrease metric shows a higher precedence inside the routing table.
True or False: You can use the equal VLAN ID for more than one VLANs in your firewall. *
True
False - ANS-False
Each VLAN have to have a unique ID.
What are the benefits of Link Aggregation? Select all that apply. *
A) Allows you to bridge interfaces so your firewall can act as a switch.
For each VLAN interface, what number of untagged networks can you have? *
A) One
B) Four
C) Unlimited
D) Dependent at the firewall model - ANS-A
In order to study the site visitors that passes over you HTTP coverage, what do you need to
make certain to do first? *
A) Turn up Diagnostic Logging underneath the Setup > Logging menu.
B) Turn on logging inside of WebBlocker.
C) No trade wishes to be made. All guidelines log by default.
D) Turn on Logging within the HTTP policy. - ANS-D
True or False: A Feature Key may be migrated among gadgets. *
True
False - ANS-False
A Feature Key is specific to a selected device, due to the fact it's far based at the serial quantity.
True or False: A packet clear out is the maximum stable way to pass traffic thru your firewall. *
True
False - ANS-False.
A packet filter out definitely critiques the header statistics of a packet. A proxy is what allows for
greater in-depth filtering of the site visitors, for that reason presenting extra security.
True or False: APT Blocker requires that Gateway Antivirus be enabled. *
True
False - ANS-True.
APT Blocker uses the equal scanning engine as APT Blocker, so the GAV carrier must first be
enabled.
True or False: In order for a Branch Office VPN to be built the Tunnel have to be installed first. *
True
False - ANS-False.
The Gateway should set up first.
, True or False: In order to allow NAT Loopback on your firewall, you need to configure this under
the Dynamic NAT settings. *
True
False - ANS-False.
NAT Loopback does no longer require whatever to be enabled. You easy must write a coverage
to allow it.
True or False: Policy precedence is most often decided via the alphabetical order of coverage
names. *
True
False - ANS-False.
Policy precedence is determined via how precise the policy is with reference to what visitors is
permitted.
True or False: There are 3 modes you can operate your firewall below: Mixed Routing, Bridged
and Drop-In. Bridged mode is the default choice. *
True
False - ANS-False.
Mixed Routing mode is the default mode.
True or False: Through Firebox System Manager, you may run the TCP Dump command. *
True
False - ANS-True.
This choice is available beneath the Diagnostic Tasks tool.
True or False: When putting in place a static path, a lower metric approach a lower precedence.
*
True
False - ANS-False
A decrease metric shows a higher precedence inside the routing table.
True or False: You can use the equal VLAN ID for more than one VLANs in your firewall. *
True
False - ANS-False
Each VLAN have to have a unique ID.
What are the benefits of Link Aggregation? Select all that apply. *
A) Allows you to bridge interfaces so your firewall can act as a switch.
