CALIFORNIA MASONRY CONTRACTOR (C-29) LICENSE EXAM -
PRACTICE QUESTIONS FOR ACTUAL EXAMS AND 100%
CORRECT ANSWERS VERIFIED | FULL EXAM PREP TESTBANK |
INSTANT PDF DOWNLOAD | GUARANTEED PASS
CORE DOMAINS:
1. Planning and Estimation
2. Preparation and Site Work
3. Brick and Block Masonry
4. Stone Masonry
5. Glass Block Masonry
6. Masonry Veneer and Retaining Walls
7. Maintenance and Repair
8. Safety and California Building Code (Title 24)
,This comprehensive test bank is designed for professionals seeking
the C-29 Masonry Contractor License in California. It covers advanced
technical theory, California-specific building codes, structural
reinforcement requirements, and job-site safety standards. These
questions simulate the complexity and depth found in the official state
examination to ensure mastery of the trade.
SECTION 1: Questions 1–100
1. What is the maximum height a mason can build a single-wythe
brick wall before it requires temporary bracing according to
OSHA standards?
ANS: 8 feet
2. When estimating for a CMU wall, how many standard 8x8x16
blocks are typically required to cover 100 square feet of wall
surface?
ANS: 112.5 blocks
,3. Which type of mortar is specifically recommended for reinforced
masonry in high-seismic regions like California?
ANS: Type S
4. What is the minimum required lap for #4 rebar in a masonry bond
beam when not specified otherwise?
ANS: 24 inches (or 48 bar diameters)
5. In stone masonry, what term refers to the process of filling the
surface joints with high-quality mortar to protect against
moisture?
ANS: Pointing
6. According to the California Building Code, what is the minimum
clearance between masonry veneer and the wood stud backing?
ANS: 1 inch
7. What type of brick is designed for use in areas where they will be
exposed to freezing temperatures while saturated with water?
, ANS: Grade SW (Severe Weathering)
8. What is the standard thickness of a mortar joint for concrete
masonry units?
ANS: 3/8 inch
9. When constructing a retaining wall, what is the primary purpose
of "weep holes"?
ANS: To relieve hydrostatic pressure behind the wall
10. Which additive is used to accelerate the setting time of mortar in
cold weather applications?
ANS: Calcium chloride
11. What is the nominal size of a standard modular brick?
ANS: 4" x 2-2/3" x 8"
12. A C-29 contractor is building a masonry chimney; what is the
minimum required clearance from combustible materials?
ANS: 2 inches
PRACTICE QUESTIONS FOR ACTUAL EXAMS AND 100%
CORRECT ANSWERS VERIFIED | FULL EXAM PREP TESTBANK |
INSTANT PDF DOWNLOAD | GUARANTEED PASS
CORE DOMAINS:
1. Planning and Estimation
2. Preparation and Site Work
3. Brick and Block Masonry
4. Stone Masonry
5. Glass Block Masonry
6. Masonry Veneer and Retaining Walls
7. Maintenance and Repair
8. Safety and California Building Code (Title 24)
,This comprehensive test bank is designed for professionals seeking
the C-29 Masonry Contractor License in California. It covers advanced
technical theory, California-specific building codes, structural
reinforcement requirements, and job-site safety standards. These
questions simulate the complexity and depth found in the official state
examination to ensure mastery of the trade.
SECTION 1: Questions 1–100
1. What is the maximum height a mason can build a single-wythe
brick wall before it requires temporary bracing according to
OSHA standards?
ANS: 8 feet
2. When estimating for a CMU wall, how many standard 8x8x16
blocks are typically required to cover 100 square feet of wall
surface?
ANS: 112.5 blocks
,3. Which type of mortar is specifically recommended for reinforced
masonry in high-seismic regions like California?
ANS: Type S
4. What is the minimum required lap for #4 rebar in a masonry bond
beam when not specified otherwise?
ANS: 24 inches (or 48 bar diameters)
5. In stone masonry, what term refers to the process of filling the
surface joints with high-quality mortar to protect against
moisture?
ANS: Pointing
6. According to the California Building Code, what is the minimum
clearance between masonry veneer and the wood stud backing?
ANS: 1 inch
7. What type of brick is designed for use in areas where they will be
exposed to freezing temperatures while saturated with water?
, ANS: Grade SW (Severe Weathering)
8. What is the standard thickness of a mortar joint for concrete
masonry units?
ANS: 3/8 inch
9. When constructing a retaining wall, what is the primary purpose
of "weep holes"?
ANS: To relieve hydrostatic pressure behind the wall
10. Which additive is used to accelerate the setting time of mortar in
cold weather applications?
ANS: Calcium chloride
11. What is the nominal size of a standard modular brick?
ANS: 4" x 2-2/3" x 8"
12. A C-29 contractor is building a masonry chimney; what is the
minimum required clearance from combustible materials?
ANS: 2 inches
