SOS Mechanic Certification Test– Brakes: Questions
With Right Solutions
Save
Terms in this set (83)
Most 1995 & newer vehicles use which Sealed non-serviceable
of the following types of wheels
bearings on non-drive wheel?
to test a vacuum power brake booster drop slightly and remain firm
in the vehicle, you should pump the
brake pedal at least 4 times, hold the
brake pedal depressed, and start the
engine. the brake pedal should:
You are installing a set of brake shoe Smaller and goes towards the front of the car.
linings that are not the same length.
Traditionally, the primary shoe lining is:
A cracked or torn vacuum diaphragm a hard pedal feel requiring very high pedal effort to
in a brake power booster would most stop
likely cause:
A mechanic finds gear lube inside A plugged axle
both rear brake drums on a rear wheel
drive vehicle. What is the most likely
cause of this problem?
Which of the following incorrect master cylinder push rod adjusted too long
service procedures will cause brake
lock-up?
, Which of the following describes the Pump the brake pedal at least 25 times (or more,
proper way to depressurized an ABS depending on the manufacturer's recommendation)
system? with the ignition off.
The rear brakes are dragging after technician use the parking brake to adjust shoes and
having new linings installed and the the cable is stuck
drums machined. the most likely cause
is the:
When turning brake drums: use a dampening strap to reduce chatter
Which of the following is NOT a run-out
necessary drum brake measurement?
On a 3-channel system, which wheels both rear wheels
are on the same circuit?
One way to test an ABS wheel speed AC volts
signal is to use _____ on your digital
multimeter.
The key input for the ABS control wheel speed sensors
module comes from the:
ABS speed sensor and sensor rings: should not be hammered or tapped on and should
always be replaced as a matched set
Flexible brake hoses should be when dampness is evident on the hose
replaced:
Which of the following should be Micrometer
used to check for rotor thickness
variation:
After rebuilding a master cylinder, the adjusted properly
rod between the master cylinder and
booster should be:
With Right Solutions
Save
Terms in this set (83)
Most 1995 & newer vehicles use which Sealed non-serviceable
of the following types of wheels
bearings on non-drive wheel?
to test a vacuum power brake booster drop slightly and remain firm
in the vehicle, you should pump the
brake pedal at least 4 times, hold the
brake pedal depressed, and start the
engine. the brake pedal should:
You are installing a set of brake shoe Smaller and goes towards the front of the car.
linings that are not the same length.
Traditionally, the primary shoe lining is:
A cracked or torn vacuum diaphragm a hard pedal feel requiring very high pedal effort to
in a brake power booster would most stop
likely cause:
A mechanic finds gear lube inside A plugged axle
both rear brake drums on a rear wheel
drive vehicle. What is the most likely
cause of this problem?
Which of the following incorrect master cylinder push rod adjusted too long
service procedures will cause brake
lock-up?
, Which of the following describes the Pump the brake pedal at least 25 times (or more,
proper way to depressurized an ABS depending on the manufacturer's recommendation)
system? with the ignition off.
The rear brakes are dragging after technician use the parking brake to adjust shoes and
having new linings installed and the the cable is stuck
drums machined. the most likely cause
is the:
When turning brake drums: use a dampening strap to reduce chatter
Which of the following is NOT a run-out
necessary drum brake measurement?
On a 3-channel system, which wheels both rear wheels
are on the same circuit?
One way to test an ABS wheel speed AC volts
signal is to use _____ on your digital
multimeter.
The key input for the ABS control wheel speed sensors
module comes from the:
ABS speed sensor and sensor rings: should not be hammered or tapped on and should
always be replaced as a matched set
Flexible brake hoses should be when dampness is evident on the hose
replaced:
Which of the following should be Micrometer
used to check for rotor thickness
variation:
After rebuilding a master cylinder, the adjusted properly
rod between the master cylinder and
booster should be:
