MSSC Quality Practice Test Questions
and Answers
What are the two types of assembly drawings? - ANS-Exploded and basic
The three standard views of an object are ____________ - ANS-top, front, right side
Geometric dimensioning and tolerances refers to tolerances which control - ANS-Form,
profile, orientation, location, and runout
Which type of feature is parallel to the surface being dimensioned? - ANS-dimension
lines
To establish on a drawing that 1/8 inch equals 1 inch, the designer would write
____________. - ANS-1/8 = 1
What is the most important item to appear on the calibration label of a tool that is used
to measure and test equipment? - ANS-The date the tool is due for calibration
The MOST important measure of external quality is product performance as viewed by
the - ANS-customer
The first step in dimensional measurement is to align the end of the rule where the zero
is located with one edge of the dimension you want to measure. This edge is called the
__________. - ANS-reference point
Multiple people sign off on Corrective Action Reports in order to ensure - ANS-that the
information is accurate
A measurement made with a precision measurement tool can be as precise as
_______. - ANS-0.001 inches
A surface plate is always - ANS-Used as a reference surface
A typical dial or digital caliper can be used to measure dimensions to the nearest
__________ inches. - ANS-0.001
Calibration means to __________. - ANS-Adjust a device to a standard
, If a worker notices that there seems to be an increasing number of defects from a
specific line, what should that worker do? - ANS-Report defects to the appropriate
contact
One of the advantages of a __________ is the measurement can be interpreted more
quickly than other precision measurement devices. - ANS-digital caliber
SPC data can be collected and transferred to a PC from what device? - ANS-a digital
caliper
The accuracy of a digital caliper reading is about __________ inches. - ANS-0.001
The micrometer is______________. - ANS-the most accurate of all hand held devices
In a Corrective Action Report, the answer to "What Were the Results?" must include -
ANS-Data that demonstrates the effectiveness of the action
A micrometer increments how far for each complete rotation of the thimble? - ANS-
0.025
Design Failure Mode and Effect Analysis (DFMEA) should be conducted - ANS-As early
as possible in the design process
To ensure the accuracy of a Standard Operating Procedure it needs to be - ANS-
Validated and approved
Of the four questions answered on a Corrective Action Report, which answer is used to
determine if a corrective action has taken place? - ANS-What were the results?
The data collected from quality checks is shared with - ANS-Everyone involved
Stored data reports should - ANS-be kept for as long as the part is produced
A _____________ is the total amount by which a specified dimension is allowed to vary
and still be a good part. - ANS-tolerance
Company standard determine how often __________ is performed. - ANS-Calibration of
hand tools
Image magnification is used in what type of device? - ANS-optical comparator
___________ measures the difference between an object's dimension and an object of
know length. - ANS-indirect comparison
Metals that contain iron, such as steel are called __________ metals. - ANS-ferrous
and Answers
What are the two types of assembly drawings? - ANS-Exploded and basic
The three standard views of an object are ____________ - ANS-top, front, right side
Geometric dimensioning and tolerances refers to tolerances which control - ANS-Form,
profile, orientation, location, and runout
Which type of feature is parallel to the surface being dimensioned? - ANS-dimension
lines
To establish on a drawing that 1/8 inch equals 1 inch, the designer would write
____________. - ANS-1/8 = 1
What is the most important item to appear on the calibration label of a tool that is used
to measure and test equipment? - ANS-The date the tool is due for calibration
The MOST important measure of external quality is product performance as viewed by
the - ANS-customer
The first step in dimensional measurement is to align the end of the rule where the zero
is located with one edge of the dimension you want to measure. This edge is called the
__________. - ANS-reference point
Multiple people sign off on Corrective Action Reports in order to ensure - ANS-that the
information is accurate
A measurement made with a precision measurement tool can be as precise as
_______. - ANS-0.001 inches
A surface plate is always - ANS-Used as a reference surface
A typical dial or digital caliper can be used to measure dimensions to the nearest
__________ inches. - ANS-0.001
Calibration means to __________. - ANS-Adjust a device to a standard
, If a worker notices that there seems to be an increasing number of defects from a
specific line, what should that worker do? - ANS-Report defects to the appropriate
contact
One of the advantages of a __________ is the measurement can be interpreted more
quickly than other precision measurement devices. - ANS-digital caliber
SPC data can be collected and transferred to a PC from what device? - ANS-a digital
caliper
The accuracy of a digital caliper reading is about __________ inches. - ANS-0.001
The micrometer is______________. - ANS-the most accurate of all hand held devices
In a Corrective Action Report, the answer to "What Were the Results?" must include -
ANS-Data that demonstrates the effectiveness of the action
A micrometer increments how far for each complete rotation of the thimble? - ANS-
0.025
Design Failure Mode and Effect Analysis (DFMEA) should be conducted - ANS-As early
as possible in the design process
To ensure the accuracy of a Standard Operating Procedure it needs to be - ANS-
Validated and approved
Of the four questions answered on a Corrective Action Report, which answer is used to
determine if a corrective action has taken place? - ANS-What were the results?
The data collected from quality checks is shared with - ANS-Everyone involved
Stored data reports should - ANS-be kept for as long as the part is produced
A _____________ is the total amount by which a specified dimension is allowed to vary
and still be a good part. - ANS-tolerance
Company standard determine how often __________ is performed. - ANS-Calibration of
hand tools
Image magnification is used in what type of device? - ANS-optical comparator
___________ measures the difference between an object's dimension and an object of
know length. - ANS-indirect comparison
Metals that contain iron, such as steel are called __________ metals. - ANS-ferrous
