1|Page
NWSA TT1 Exam 2026/2027 || Most Recent Exam
Actual Complete Real Verified Exam Questions And
Correct Answers (Verified Answers) Already Graded |
Guaranteed Success!! Newest Exam!!!
If you have a sixteen foot ladder leaning against a building
wall, how many feet from the wall does the case need to
by to have the correct slope? - Answer-4
Work boots with ankle support are recommended for all
work sites? - Answer-True
What do the letters PPE stand for ? - Answer-Personal
Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? -
Answer-Senses a short circuit, prevents electrocution ,
shuts off the flow of electricity
Who is responsible for providing PPE? - Answer-Employer
,2|Page
When using a y-lanyard attached to your back d-ring, at
what height should the connection to your anchorage be
placed?extend? - Answer-Shoulder level or above
What is the maximum distance between the sternal d-ring
and the fixed safety climb? - Answer-Nine inches
When calculating a fall distance using a "6 foot" energy
absorbed, what is the maximum pull out distance? -
Answer-Four feey
What is the minimum force that a work positioning system
anchorage must be able to withstand? - Answer-Two times
the arresting force of 3000lbs
What minimum force must a non-engineered anchor be
able to withstand for fall protection use? - Answer-5,000
lbs
When working, how often should fall protection equipment
be inspected ? - Answer-Daily before each use
, 3|Page
According to the applicable industry standard, what is the
minimum height from a lower surface or ground where fall
protection must be used? - Answer-Six feet
Who is the third party group that approves and endorses
standards? - Answer-American National Standards
Institute
What term is used to describe the documents written by
members, or peers, in the industry? - Answer-Standards
A company's health, safety and environment policy should
be a combination of labor regulations and ? - Answer-
Industry standards
Where OSHA has not promulgated specific standards,
who is responsible for following the acts general clause? -
Answer-Employer
On a job site who should be involved in the JHA process?
- Answer-The Whole Crew
What does the Term SOW stand for? - Answer-Scope Of
Work
NWSA TT1 Exam 2026/2027 || Most Recent Exam
Actual Complete Real Verified Exam Questions And
Correct Answers (Verified Answers) Already Graded |
Guaranteed Success!! Newest Exam!!!
If you have a sixteen foot ladder leaning against a building
wall, how many feet from the wall does the case need to
by to have the correct slope? - Answer-4
Work boots with ankle support are recommended for all
work sites? - Answer-True
What do the letters PPE stand for ? - Answer-Personal
Protective Equipment
What does the ground fault circuit interrupter (GFCI) do? -
Answer-Senses a short circuit, prevents electrocution ,
shuts off the flow of electricity
Who is responsible for providing PPE? - Answer-Employer
,2|Page
When using a y-lanyard attached to your back d-ring, at
what height should the connection to your anchorage be
placed?extend? - Answer-Shoulder level or above
What is the maximum distance between the sternal d-ring
and the fixed safety climb? - Answer-Nine inches
When calculating a fall distance using a "6 foot" energy
absorbed, what is the maximum pull out distance? -
Answer-Four feey
What is the minimum force that a work positioning system
anchorage must be able to withstand? - Answer-Two times
the arresting force of 3000lbs
What minimum force must a non-engineered anchor be
able to withstand for fall protection use? - Answer-5,000
lbs
When working, how often should fall protection equipment
be inspected ? - Answer-Daily before each use
, 3|Page
According to the applicable industry standard, what is the
minimum height from a lower surface or ground where fall
protection must be used? - Answer-Six feet
Who is the third party group that approves and endorses
standards? - Answer-American National Standards
Institute
What term is used to describe the documents written by
members, or peers, in the industry? - Answer-Standards
A company's health, safety and environment policy should
be a combination of labor regulations and ? - Answer-
Industry standards
Where OSHA has not promulgated specific standards,
who is responsible for following the acts general clause? -
Answer-Employer
On a job site who should be involved in the JHA process?
- Answer-The Whole Crew
What does the Term SOW stand for? - Answer-Scope Of
Work
