LOW PRESSURE BOILER BLACK SEAL QUESTIONS AND
ANSWERS NEWEST RATED A+ 2025/2026 NEW!!
Where on the Certificate of Inspection would you find the State of New Jersey jurisdiction
number? - Answers upper left corner
Which of the following best describes the combustion chamber of a serpentine tube heating
boiler? - Answers it is located below the tubes
By N.J.A.C. rules, a school with a boiler plant with a total interconnected capacity of 100 BHP
would require a properly licensed operator to be present whenever the building was deemed
occupied. - Answers false
Which of the following is not a classification of a hot water system? - Answers a Hartford loop
system
When bringing a steam heating plant on line from a cold start, when the ambient conditions
are about 20 degrees F, what condition are you preventing when the pressure is increased
gradually? - Answers thermal shock
A boiler operator's log shall be maintained in each plant containing over: - Answers 100
Boiler HP
By definition, a boiler is an open vessel in which water is turned to steam under pressure by the
application of heat. - Answers false
According to state boiler regulations, where should the boiler registration number be located? -
Answers on the front of the boiler
, As an operator in a plant you must always be aware of your surroundings. Which of the
following, that should be under the control of the licensed operator, can be extremely
dangerous and cause a catastrophic hazardous event if it is not inspected annually? - Answers
The boiler(s) can be dangerous if not inspected and maintained properly
The primary purpose of establishing a set of plant safety rules is to: - Answers protect
workers and equipment
The ASME Code states that the setting on the high limit pressure control on a low pressure
steam boiler shall not exceed: - Answers 15 psig
In order to be a good operator one must have basic knowledge on the principles of how energy
works in a steam and hot water system. Which of the statements below is correct? - Answers
in a heating system, in order to change state from a liquid to a gaseous state heat must be
added.
What ASME code section is used for the care and operation of heating boilers? - Answers
ASME Code, Section VI
In a hot water heating system, where would you find an expansion tank and what is its
function? - Answers on the suction side of the pump to avoid negative pressure in the system
What is the official ASME letter stamp used to denote low pressure heating boilers? - Answers
H
What is the maximum penalty for performing the duties of a boiler operator with an expired
license? - Answers $5,000.00
What is the purpose of an aquastat control device on a boiler system? - Answers it is used to
control water temperature
ANSWERS NEWEST RATED A+ 2025/2026 NEW!!
Where on the Certificate of Inspection would you find the State of New Jersey jurisdiction
number? - Answers upper left corner
Which of the following best describes the combustion chamber of a serpentine tube heating
boiler? - Answers it is located below the tubes
By N.J.A.C. rules, a school with a boiler plant with a total interconnected capacity of 100 BHP
would require a properly licensed operator to be present whenever the building was deemed
occupied. - Answers false
Which of the following is not a classification of a hot water system? - Answers a Hartford loop
system
When bringing a steam heating plant on line from a cold start, when the ambient conditions
are about 20 degrees F, what condition are you preventing when the pressure is increased
gradually? - Answers thermal shock
A boiler operator's log shall be maintained in each plant containing over: - Answers 100
Boiler HP
By definition, a boiler is an open vessel in which water is turned to steam under pressure by the
application of heat. - Answers false
According to state boiler regulations, where should the boiler registration number be located? -
Answers on the front of the boiler
, As an operator in a plant you must always be aware of your surroundings. Which of the
following, that should be under the control of the licensed operator, can be extremely
dangerous and cause a catastrophic hazardous event if it is not inspected annually? - Answers
The boiler(s) can be dangerous if not inspected and maintained properly
The primary purpose of establishing a set of plant safety rules is to: - Answers protect
workers and equipment
The ASME Code states that the setting on the high limit pressure control on a low pressure
steam boiler shall not exceed: - Answers 15 psig
In order to be a good operator one must have basic knowledge on the principles of how energy
works in a steam and hot water system. Which of the statements below is correct? - Answers
in a heating system, in order to change state from a liquid to a gaseous state heat must be
added.
What ASME code section is used for the care and operation of heating boilers? - Answers
ASME Code, Section VI
In a hot water heating system, where would you find an expansion tank and what is its
function? - Answers on the suction side of the pump to avoid negative pressure in the system
What is the official ASME letter stamp used to denote low pressure heating boilers? - Answers
H
What is the maximum penalty for performing the duties of a boiler operator with an expired
license? - Answers $5,000.00
What is the purpose of an aquastat control device on a boiler system? - Answers it is used to
control water temperature
