Michigan State Brakes Cer fica on| With complete
solu on| Updated 2026 | New edi on
Most 1995 & newer vehicles use which of the following types of wheels bearings on non-drive
wheel?
Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake pedal at least
4 "mes, hold the brake pedal depressed, and start the engine. the brake pedal should:
drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length. Tradi"onally, the
primary shoe lining is:
Smaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely cause:
a hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive vehicle. What is
the most likely cause of this problem?
A plugged axle
Which of the following incorrect service procedures will cause brake lock-up?
master cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an ABS system?
Pump the brake pedal at least 25 "mes (or more, depending on the manufacturer's
recommenda"on) with the igni"on off.
The rear brakes are dragging a5er having new linings installed and the drums machined. the
most likely cause is the:
technician use the parking brake to adjust shoes and the cable is stuck
When turning brake drums:
use a dampening strap to reduce cha6er
, Which of the following is NOT a necessary drum brake measurement?
run-out
On a 3-channel system, which wheels are on the same circuit?
both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital mul"meter.
AC volts
The key input for the ABS control module comes from the:
wheel speed sensors
ABS speed sensor and sensor rings:
should not be hammered or tapped on and should always be replaced as a matched set
Flexible brake hoses should be replaced:
when dampness is evident on the hose
Which of the following should be used to check for rotor thickness varia"on:
Micrometer
A5er rebuilding a master cylinder, the rod between the master cylinder and booster should be:
adjusted properly
Upon inspec"ng brake fluid condi"on, the technician observes the diaphragm in the master
cylinder cup is swollen. Which of the following is the most likely cause?
silicone fluid added to the system
When inspec"ng brake fluid levels, a technician observes low fluid levels. which of the following
should be done first?
Inspect disc brake pads for excessive wear
Which of the following is true about most properly func"oning an"-lock brake systems?
The brakes may lock up at speeds less than 10 miles per hour
Which of the following is true about bleeding brake lines on most ABS equipped vehicles?
Most ABS brake lines can be bled like a conven"onal (non-ABS) system. However, cau"on must
be taken because of the extreme pressure.
solu on| Updated 2026 | New edi on
Most 1995 & newer vehicles use which of the following types of wheels bearings on non-drive
wheel?
Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake pedal at least
4 "mes, hold the brake pedal depressed, and start the engine. the brake pedal should:
drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length. Tradi"onally, the
primary shoe lining is:
Smaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely cause:
a hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive vehicle. What is
the most likely cause of this problem?
A plugged axle
Which of the following incorrect service procedures will cause brake lock-up?
master cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an ABS system?
Pump the brake pedal at least 25 "mes (or more, depending on the manufacturer's
recommenda"on) with the igni"on off.
The rear brakes are dragging a5er having new linings installed and the drums machined. the
most likely cause is the:
technician use the parking brake to adjust shoes and the cable is stuck
When turning brake drums:
use a dampening strap to reduce cha6er
, Which of the following is NOT a necessary drum brake measurement?
run-out
On a 3-channel system, which wheels are on the same circuit?
both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital mul"meter.
AC volts
The key input for the ABS control module comes from the:
wheel speed sensors
ABS speed sensor and sensor rings:
should not be hammered or tapped on and should always be replaced as a matched set
Flexible brake hoses should be replaced:
when dampness is evident on the hose
Which of the following should be used to check for rotor thickness varia"on:
Micrometer
A5er rebuilding a master cylinder, the rod between the master cylinder and booster should be:
adjusted properly
Upon inspec"ng brake fluid condi"on, the technician observes the diaphragm in the master
cylinder cup is swollen. Which of the following is the most likely cause?
silicone fluid added to the system
When inspec"ng brake fluid levels, a technician observes low fluid levels. which of the following
should be done first?
Inspect disc brake pads for excessive wear
Which of the following is true about most properly func"oning an"-lock brake systems?
The brakes may lock up at speeds less than 10 miles per hour
Which of the following is true about bleeding brake lines on most ABS equipped vehicles?
Most ABS brake lines can be bled like a conven"onal (non-ABS) system. However, cau"on must
be taken because of the extreme pressure.
