Page 1 of 31
NACE CIP 1 CBT PRACTICE EXAM |
FREQUENTLY TESTED QUESTIONS WITH
CORRECT ANSWERS | BRAND NEW!
Which joint NACE/SSPC abrasive blasting standard states that
"Random staying shall be limited to no more than 33% of each
unit surface area"? - ✔✔✔ Correct Answer > NACE No. 3/SSPC SP 6
Commercial Blast Cleaning
What is the minimum spot measurement value allowed by SSPC-
PA 2 in each 10 m2 (100ft0 area/ - ✔✔✔ Correct Answer > 80% of the
specified minimum thickness.
Stripe coats are best applied by: - ✔✔✔ Correct Answer > Brush
The Inspector should record the serial numbers of inspection
instruments: - ✔✔✔ Correct Answer > Each time the instrument is
used.
ISO SA 3 is directly equivalent to: - ✔✔✔ Correct Answer > NACE
No.1/SSPC SP 5
,Page 2 of 31
On a blast cleaned surface, an ultraviolet light is generally used
to detect: - ✔✔✔ Correct Answer > Grease and Oil
You are the NACE Inspector on a job where NACE No.2/SSPC SP
10 has been specified. Your are finding the Contractor is leaving
mill scale on the surface and as a result you have been rejecting
the blast. The Contractor is very upset and has told you that the
standard permits up to 5% of the mills scale to remain and still
be in compliance with the standard. Your FIRST preferred course
if action is to: - ✔✔✔ Correct Answer > Review the relevant standard
with the Contractor.
A successful coating Inspector must be able to: - ✔✔✔ Correct Answer
> Look for problems and issues during application.
A magnetic pull off type gauge is a good choice when: - ✔✔✔ Correct
Answer > When an intrinsically safe tool is required.
The Inspector's log book is generally: - ✔✔✔ Correct Answer >
Retained by the inspector upon project completion.
The most important factor resulting in improved job site safety is:
- ✔✔✔ Correct Answer > Situational Awareness
,Page 3 of 31
You are the NACE Inspector on a 5,000 sq ft job where SSPC PA 2
has been specified.Assuming all areas are in compliance, how
many gauge readings and spot measurements are required? -
✔✔✔ Correct Answer > 225 gauge readings resulting in 75 spot
measurements.
Stripe coats are generally applied to: - ✔✔✔ Correct Answer > Edges,
corners, welds and complex geometric shapes.
SSPC SP 1 identifies the use of: - ✔✔✔ Correct Answer > A wide variety
of materials.
Which one of the following documents is the best source for
coating technical data: - ✔✔✔ Correct Answer > Technical Data Sheet
Which is a component that supplies most of the features and
functions of the material? - ✔✔✔ Correct Answer > Binder
NACE Level 1 Inspectors have been trained to perform: - ✔✔✔
Correct Answer > Visual inspection and non destructive testing.
If a Thermoset coating is heated it will: - ✔✔✔ Correct Answer >
Harden and retain its hardness when cooled.
, Page 4 of 31
As a NACE Coating Inspector your responsibility with respect to
safety is to: - ✔✔✔ Correct Answer > Act in accordance with the site
safety requirements and set an example.
Prior to using Inspection tools the inspector must: - ✔✔✔ Correct
Answer > Ensure the instrument is within calibration parameters,
be trained on how to use the equipment and read the
manufactures instructions.
When the joint NACE/SSPC abrasive blast cleaning standards are
specified, the pictures in SSPC VIS 1 can be used as: - ✔✔✔ Correct
Answer > A general guide.
You are the NACE Coating Inspector on an exterior job where the
Contractor is not using any environmental controls. For the last
several hours your reading; indicates the relative humidity is
rising and the substrate temperature is dropping. The sky is
clouding over and the weather forecast is for evening showers. It
is now 4PM, your readings indicate you have minimally
acceptable environmental conditions, however if the current
trend continues you expect to be outside specified conditions
soon. The contractor advises you he is going to mis up the next
full kit to complete his job for the day. Your FIRST performed
course of action is to: - ✔✔✔ Correct Answer > Advise the Contractor
of your readings.
NACE CIP 1 CBT PRACTICE EXAM |
FREQUENTLY TESTED QUESTIONS WITH
CORRECT ANSWERS | BRAND NEW!
Which joint NACE/SSPC abrasive blasting standard states that
"Random staying shall be limited to no more than 33% of each
unit surface area"? - ✔✔✔ Correct Answer > NACE No. 3/SSPC SP 6
Commercial Blast Cleaning
What is the minimum spot measurement value allowed by SSPC-
PA 2 in each 10 m2 (100ft0 area/ - ✔✔✔ Correct Answer > 80% of the
specified minimum thickness.
Stripe coats are best applied by: - ✔✔✔ Correct Answer > Brush
The Inspector should record the serial numbers of inspection
instruments: - ✔✔✔ Correct Answer > Each time the instrument is
used.
ISO SA 3 is directly equivalent to: - ✔✔✔ Correct Answer > NACE
No.1/SSPC SP 5
,Page 2 of 31
On a blast cleaned surface, an ultraviolet light is generally used
to detect: - ✔✔✔ Correct Answer > Grease and Oil
You are the NACE Inspector on a job where NACE No.2/SSPC SP
10 has been specified. Your are finding the Contractor is leaving
mill scale on the surface and as a result you have been rejecting
the blast. The Contractor is very upset and has told you that the
standard permits up to 5% of the mills scale to remain and still
be in compliance with the standard. Your FIRST preferred course
if action is to: - ✔✔✔ Correct Answer > Review the relevant standard
with the Contractor.
A successful coating Inspector must be able to: - ✔✔✔ Correct Answer
> Look for problems and issues during application.
A magnetic pull off type gauge is a good choice when: - ✔✔✔ Correct
Answer > When an intrinsically safe tool is required.
The Inspector's log book is generally: - ✔✔✔ Correct Answer >
Retained by the inspector upon project completion.
The most important factor resulting in improved job site safety is:
- ✔✔✔ Correct Answer > Situational Awareness
,Page 3 of 31
You are the NACE Inspector on a 5,000 sq ft job where SSPC PA 2
has been specified.Assuming all areas are in compliance, how
many gauge readings and spot measurements are required? -
✔✔✔ Correct Answer > 225 gauge readings resulting in 75 spot
measurements.
Stripe coats are generally applied to: - ✔✔✔ Correct Answer > Edges,
corners, welds and complex geometric shapes.
SSPC SP 1 identifies the use of: - ✔✔✔ Correct Answer > A wide variety
of materials.
Which one of the following documents is the best source for
coating technical data: - ✔✔✔ Correct Answer > Technical Data Sheet
Which is a component that supplies most of the features and
functions of the material? - ✔✔✔ Correct Answer > Binder
NACE Level 1 Inspectors have been trained to perform: - ✔✔✔
Correct Answer > Visual inspection and non destructive testing.
If a Thermoset coating is heated it will: - ✔✔✔ Correct Answer >
Harden and retain its hardness when cooled.
, Page 4 of 31
As a NACE Coating Inspector your responsibility with respect to
safety is to: - ✔✔✔ Correct Answer > Act in accordance with the site
safety requirements and set an example.
Prior to using Inspection tools the inspector must: - ✔✔✔ Correct
Answer > Ensure the instrument is within calibration parameters,
be trained on how to use the equipment and read the
manufactures instructions.
When the joint NACE/SSPC abrasive blast cleaning standards are
specified, the pictures in SSPC VIS 1 can be used as: - ✔✔✔ Correct
Answer > A general guide.
You are the NACE Coating Inspector on an exterior job where the
Contractor is not using any environmental controls. For the last
several hours your reading; indicates the relative humidity is
rising and the substrate temperature is dropping. The sky is
clouding over and the weather forecast is for evening showers. It
is now 4PM, your readings indicate you have minimally
acceptable environmental conditions, however if the current
trend continues you expect to be outside specified conditions
soon. The contractor advises you he is going to mis up the next
full kit to complete his job for the day. Your FIRST performed
course of action is to: - ✔✔✔ Correct Answer > Advise the Contractor
of your readings.
