1|Page
Certified Bench Jeweler (CBJ) Exam
COMPLETE||VERIFIED EXAM!!|| QUESTIONS AND
DETAILED SOLUTIONS LATEST UPDATE THIS YEAR-
JUST RELEASED.pdf||NEWEST EXAM!!!
How do you use bench pin, C clamp, and jeweler saw? -
Answer-Use the C clamp to secure the bench pin on the
table, put in jewelers saw blade by unscrewing the two
screws (top and bottom) and put the blade in with the
blade texture, facing outward and screw it back tightly
Soldering step by step: - Answer-1. Place metal on brick.
2. Apply a thin layer of flux to the areas where you will
solder. (flux prevents oxidation and helps solder flow
smoothly.)
3. Cut small pieces of solder and position it with tweezers.
4. Use third arm to hold pieces together.
5. Light torch and adjust flame.
6. Move flame evenly around the joint to heat the entire
piece.
7. When metal reaches a dull red, turn off the torch.
8. Allow peace to cool slightly and place it in pickling
solution to remove oxidation or flux residue
,2|Page
9. Rinse and dry thoroughly.
What is quenching? - Answer-When you rapidly cool the
metal by submerging in water after soldering or ahealing
What does pickle do and what tongs can you use? -
Answer-Pickle cleans by removing oxidation. Use copper
tongs because they don't react with the solution.
Sweat soldering vs joint soldering - Answer-Sweat
soldering: solder is melted onto one surface, then
reheated to join it to another. It is best for attaching flat or
layered pieces.
Joint soldering: solder joins two edges by melting and
bridging the seam It is used for structural joints, like rings,
chains or bangles.
What is annealing and how do you do it? - Answer-
Annealing is the process of heating metal to soften it
making it easier to shape bend or work with
1. Clean metal
, 3|Page
2. Apply flux (optional)
3. Heat metal
4. Cool down then quench in water
5. Put in pickle (optional)
How do you texture metal with the rolling mill? - Answer-
Place metal with textured material (lace or paper) and roll
it through for a detailed pattern
How do you texture metal with texture hammer? - Answer-
Use hammer with the patterned faces to create textures,
like crosshatches, or dimples
How do you texture metal with ball peen hammer? -
Answer-Top metal with the rounded, and for a dimple
hammered look
How do you texture metal with stamps? - Answer-Strike
metal with design stamps for sharp pattern or shapes
Certified Bench Jeweler (CBJ) Exam
COMPLETE||VERIFIED EXAM!!|| QUESTIONS AND
DETAILED SOLUTIONS LATEST UPDATE THIS YEAR-
JUST RELEASED.pdf||NEWEST EXAM!!!
How do you use bench pin, C clamp, and jeweler saw? -
Answer-Use the C clamp to secure the bench pin on the
table, put in jewelers saw blade by unscrewing the two
screws (top and bottom) and put the blade in with the
blade texture, facing outward and screw it back tightly
Soldering step by step: - Answer-1. Place metal on brick.
2. Apply a thin layer of flux to the areas where you will
solder. (flux prevents oxidation and helps solder flow
smoothly.)
3. Cut small pieces of solder and position it with tweezers.
4. Use third arm to hold pieces together.
5. Light torch and adjust flame.
6. Move flame evenly around the joint to heat the entire
piece.
7. When metal reaches a dull red, turn off the torch.
8. Allow peace to cool slightly and place it in pickling
solution to remove oxidation or flux residue
,2|Page
9. Rinse and dry thoroughly.
What is quenching? - Answer-When you rapidly cool the
metal by submerging in water after soldering or ahealing
What does pickle do and what tongs can you use? -
Answer-Pickle cleans by removing oxidation. Use copper
tongs because they don't react with the solution.
Sweat soldering vs joint soldering - Answer-Sweat
soldering: solder is melted onto one surface, then
reheated to join it to another. It is best for attaching flat or
layered pieces.
Joint soldering: solder joins two edges by melting and
bridging the seam It is used for structural joints, like rings,
chains or bangles.
What is annealing and how do you do it? - Answer-
Annealing is the process of heating metal to soften it
making it easier to shape bend or work with
1. Clean metal
, 3|Page
2. Apply flux (optional)
3. Heat metal
4. Cool down then quench in water
5. Put in pickle (optional)
How do you texture metal with the rolling mill? - Answer-
Place metal with textured material (lace or paper) and roll
it through for a detailed pattern
How do you texture metal with texture hammer? - Answer-
Use hammer with the patterned faces to create textures,
like crosshatches, or dimples
How do you texture metal with ball peen hammer? -
Answer-Top metal with the rounded, and for a dimple
hammered look
How do you texture metal with stamps? - Answer-Strike
metal with design stamps for sharp pattern or shapes
