TN BC Contractors exam questions
with answers
After installation and adequate fastening, floor decks
serve several purposes:
A. Acts as a working platform
B. Stabilizes the frame
C. Serves as concrete form for the slab
D. All the above - CORRECT ANSWERS ✔✔Steel Deck pg
6:
D. All the above
Composite floor deck is normally installed so the
__________________ - CORRECT ANSWERS ✔✔Steel Deck pg
6:
Panel ends do not overlap
Roof deck is not designed to act compositely with other
materials. The roof deck________________________ -
CORRECT ANSWERS ✔✔Steel Deck pg 7:
Acts alone in transferring horizontal and vertical loads
into the building frame.
,Roof deck is typically installed to end lap approximately
_________ inches over supports. - CORRECT ANSWERS
✔✔Steel Deck pg 7:
2"
___________________ can be used in the same manner as
floor deck. Electrical, telephone and computer wires are
easily run through the chase created between the deck
panel and the bottom sheet. - CORRECT ANSWERS
✔✔Steel Deck pg 8:
Cellular Deck
A 3' x 12" composite floor deck will have a nominal
thickness range of. 03 inches to. 06 inches and a weight
range of ____ to _____ psf - CORRECT ANSWERS ✔✔Steel
Deck pg 9:
2 to 4 psf
F deck may also be referred to as______________ for the
name,. 03 inches two. 06 inches for the thickness and 2
to 4 PSF for the weight. - CORRECT ANSWERS ✔✔Steel
Deck pg 10:
1 1/2" X 6" Intermediate Rib
,The weight range for cellular floor decking is__________ -
CORRECT ANSWERS ✔✔Steel Deck pg 12:
4 to 7 PSF
A heavy duty form decks name used in centering is______
Form deck with a thickness of_____ to _____ And a weight
range of one to two PSF - CORRECT ANSWERS ✔✔Steel
Deck pg 11:
15/16" and 0.017" to 0.040"
Steel deck is banded into bundles that can weigh several
thousand pounds but the deck bundle weight will be
limited to a maximum of_______________ For deck to be
applied to joists. - CORRECT ANSWERS ✔✔Steel Deck pg
14:
4000 lbs
If ground storage is needed, the deck bundles should
be______________ - CORRECT ANSWERS ✔✔Steel Deck pg
18:
Stored off the ground, with one end elevated to provide
drainage.
, Deck bundles must________ be placed on the frame near a
main supporting beam at a column or a wall - CORRECT
ANSWERS ✔✔Steel Deck pg 18:
ALWAYS
Bundles should be landed so that the
___________________________ rather than having one or
both ends cantilevered. - CORRECT ANSWERS ✔✔Steel
Deck pg 22:
Ends of the bundles rest on a bearing surface
Are you working area should be at least _________ feet
wide. - CORRECT ANSWERS ✔✔Steel Deck pg 24:
12
When aligning the edge (side) lap, the worker
should__________ - CORRECT ANSWERS ✔✔Steel Deck pg
25:
Kneel
Deck fastening to the structural frame can be
accomplished with: - CORRECT ANSWERS ✔✔Steel Deck
pg 28:
Welds, self drilling screws, air driven, and power driven
with answers
After installation and adequate fastening, floor decks
serve several purposes:
A. Acts as a working platform
B. Stabilizes the frame
C. Serves as concrete form for the slab
D. All the above - CORRECT ANSWERS ✔✔Steel Deck pg
6:
D. All the above
Composite floor deck is normally installed so the
__________________ - CORRECT ANSWERS ✔✔Steel Deck pg
6:
Panel ends do not overlap
Roof deck is not designed to act compositely with other
materials. The roof deck________________________ -
CORRECT ANSWERS ✔✔Steel Deck pg 7:
Acts alone in transferring horizontal and vertical loads
into the building frame.
,Roof deck is typically installed to end lap approximately
_________ inches over supports. - CORRECT ANSWERS
✔✔Steel Deck pg 7:
2"
___________________ can be used in the same manner as
floor deck. Electrical, telephone and computer wires are
easily run through the chase created between the deck
panel and the bottom sheet. - CORRECT ANSWERS
✔✔Steel Deck pg 8:
Cellular Deck
A 3' x 12" composite floor deck will have a nominal
thickness range of. 03 inches to. 06 inches and a weight
range of ____ to _____ psf - CORRECT ANSWERS ✔✔Steel
Deck pg 9:
2 to 4 psf
F deck may also be referred to as______________ for the
name,. 03 inches two. 06 inches for the thickness and 2
to 4 PSF for the weight. - CORRECT ANSWERS ✔✔Steel
Deck pg 10:
1 1/2" X 6" Intermediate Rib
,The weight range for cellular floor decking is__________ -
CORRECT ANSWERS ✔✔Steel Deck pg 12:
4 to 7 PSF
A heavy duty form decks name used in centering is______
Form deck with a thickness of_____ to _____ And a weight
range of one to two PSF - CORRECT ANSWERS ✔✔Steel
Deck pg 11:
15/16" and 0.017" to 0.040"
Steel deck is banded into bundles that can weigh several
thousand pounds but the deck bundle weight will be
limited to a maximum of_______________ For deck to be
applied to joists. - CORRECT ANSWERS ✔✔Steel Deck pg
14:
4000 lbs
If ground storage is needed, the deck bundles should
be______________ - CORRECT ANSWERS ✔✔Steel Deck pg
18:
Stored off the ground, with one end elevated to provide
drainage.
, Deck bundles must________ be placed on the frame near a
main supporting beam at a column or a wall - CORRECT
ANSWERS ✔✔Steel Deck pg 18:
ALWAYS
Bundles should be landed so that the
___________________________ rather than having one or
both ends cantilevered. - CORRECT ANSWERS ✔✔Steel
Deck pg 22:
Ends of the bundles rest on a bearing surface
Are you working area should be at least _________ feet
wide. - CORRECT ANSWERS ✔✔Steel Deck pg 24:
12
When aligning the edge (side) lap, the worker
should__________ - CORRECT ANSWERS ✔✔Steel Deck pg
25:
Kneel
Deck fastening to the structural frame can be
accomplished with: - CORRECT ANSWERS ✔✔Steel Deck
pg 28:
Welds, self drilling screws, air driven, and power driven
