Inspect Fireplaces, Stoves, and Chimneys || with Errorless Answers.
The inspector is required to inspect the damper doors by... correct answers opening and closing
them, if readily accessible and manually operable.
The inspection is _________ chimney and fireplace structure, systems and components. correct
answers a visual-only evaluation of the accessible
The inspector should advise his/her client that all fireplaces, fuel-burning stoves, and chimneys
should be inspected by a __________ prior to their first use, and not less than annually. correct
answers certified chimney sweep
What is the vent type material for chimney connection? correct answers Type L vent material
At a masonry chimney flue, the connector vent pipe must connect at a point at least ____ inches
above the lowest portion of the interior of the chimney flue correct answers 12 inches
Chimney connectors should be sloped at least ____ of rise per ____ of run. correct answers 1/4-
inch
foot
Chimney connector joints should be fastened with.... correct answers sheet metal screws or
rivets.
A single-wall metal pipe used as a vent connector passing through a wall, ceiling or floor must be
guarded by a ventilated, non-combustible metal thimble, and must maintain a minimum
clearance of ____ inches between the thimble and any combustibles correct answers 6 inches
Inlets to masonry chimneys must enter from...... correct answers the side
, A masonry chimney should extend at least _____ feet above the highest point where the chimney
passes through the roof, and _____ feet above any portion of a building that is within a _____-
foot distance horizontally. correct answers 3, 2, 10
Chimney clearance. House framing components should be at least _____ away from the chimney
wall. correct answers 2 inches
Footings for masonry chimneys must be made of concrete or solid masonry at least ________
correct answers 1 foot thick.
Masonry chimneys should extend at least _____ beyond the face of the fireplace or foundation
wall on all sides. correct answers 6 inches
The size of the chimney depends on the ...... correct answers number and size of the flues
The minimum standard thickness for a flue lining is .... correct answers 5/8-inch thick.
Gas vents that are greater than 12 inches in size or that are located less than 8 feet from a vertical
wall or similar structure should terminate at least ___ feet above the highest point where they
pass through the roof, and not less than 2 feet above any portion of a dwelling within 10 feet
horizontally. correct answers 2 feet
What is needed for a fuel-gas vent above the roof is needed as the roof pitch approaches being a
vertical surface? correct answers A greater height
A cast-in-place lining ____ (can/cannot) help correct the structural integrity of an old chimney.
correct answers can
Metal chimney flue liners are usually made of _____ or aluminum. correct answers stainless
steel
The inspector is required to inspect the damper doors by... correct answers opening and closing
them, if readily accessible and manually operable.
The inspection is _________ chimney and fireplace structure, systems and components. correct
answers a visual-only evaluation of the accessible
The inspector should advise his/her client that all fireplaces, fuel-burning stoves, and chimneys
should be inspected by a __________ prior to their first use, and not less than annually. correct
answers certified chimney sweep
What is the vent type material for chimney connection? correct answers Type L vent material
At a masonry chimney flue, the connector vent pipe must connect at a point at least ____ inches
above the lowest portion of the interior of the chimney flue correct answers 12 inches
Chimney connectors should be sloped at least ____ of rise per ____ of run. correct answers 1/4-
inch
foot
Chimney connector joints should be fastened with.... correct answers sheet metal screws or
rivets.
A single-wall metal pipe used as a vent connector passing through a wall, ceiling or floor must be
guarded by a ventilated, non-combustible metal thimble, and must maintain a minimum
clearance of ____ inches between the thimble and any combustibles correct answers 6 inches
Inlets to masonry chimneys must enter from...... correct answers the side
, A masonry chimney should extend at least _____ feet above the highest point where the chimney
passes through the roof, and _____ feet above any portion of a building that is within a _____-
foot distance horizontally. correct answers 3, 2, 10
Chimney clearance. House framing components should be at least _____ away from the chimney
wall. correct answers 2 inches
Footings for masonry chimneys must be made of concrete or solid masonry at least ________
correct answers 1 foot thick.
Masonry chimneys should extend at least _____ beyond the face of the fireplace or foundation
wall on all sides. correct answers 6 inches
The size of the chimney depends on the ...... correct answers number and size of the flues
The minimum standard thickness for a flue lining is .... correct answers 5/8-inch thick.
Gas vents that are greater than 12 inches in size or that are located less than 8 feet from a vertical
wall or similar structure should terminate at least ___ feet above the highest point where they
pass through the roof, and not less than 2 feet above any portion of a dwelling within 10 feet
horizontally. correct answers 2 feet
What is needed for a fuel-gas vent above the roof is needed as the roof pitch approaches being a
vertical surface? correct answers A greater height
A cast-in-place lining ____ (can/cannot) help correct the structural integrity of an old chimney.
correct answers can
Metal chimney flue liners are usually made of _____ or aluminum. correct answers stainless
steel
