ABSA 4B FINAL EXAM 2 VERSIONS AND PRACTICE EXAM
2026-2027 BANK COMPLETE QUESTIONS AND ANSWERS
ACCURATE ACTUAL EXAM WITH FREQUENTLY TESTED
1000+ PRACTICE QUESTIONS AND STUDY GUIDE / EXPERT
VERIFIED FOR GUARANTEED PASS/ALREADY GRADED A+
BEST DOCUMENT FOR EXAM PREP
An extraction pump is not a required auxiliary component on a ____.
1. condensing steam turbine
2. non-condensing steam turbine
3. diesel engine
4. compressor
5. reciprocating engine
2. non-condensing steam turbine
When installing a it must be sized to prevent the boiler pressure rising 6%
above
the MAWP of the boiler.
1. check valve
2. boiler safety valve(s)
3. seal
4. try lever
5. low-water cut off
2. boiler safety valve(s)
,Two of the primary methods of include the sulphite and sulphate process
1. attemperator
2. chemical pulping
3. chemical evaporating
4. corrosion prevention
5. cooking liquor
2. chemical pulping
Crystallization may occur in situations where the rises above the upper
concentration limit at the lower temperature.
1. solutions lithium bromide concentration
2. solutions freon concentration
3. solutions water concentration
4. solutions air concentration
5. solutions salt concentration
5. solutions salt concentration
,The lifting capacity of the should always be verified before attempting a lift.
1. slings
2. pallet
3. lifted object
4. ratchet
5. bearings
1. slings
____ is a measure of a lubricating oils ability to support various loads.
1. Viscosity
2. Flash Point
3. Fire Point
4. Pour Point
5. Neutralization Number
1. Viscosity
, During design calculations is the absolute pressure expected at the pump
suction.
1. net positive suction head available
2. net positive suction head
3. net positive suction head required
4. net positive discharge head
5. net positive discharge head available
3. net positive suction head required
Which of the following affect the total heat loss from a building:
1. Radiation
2. Convection
3. Conduction
4. All of the above
4. All of the above
350 to 490 kPa is that typically operating pressure range of ____.
1. potable water systems
2. building water systems
3. municipal water distribution systems
4. well water systems
5. potable water systems
3. municipal water distribution systems
2026-2027 BANK COMPLETE QUESTIONS AND ANSWERS
ACCURATE ACTUAL EXAM WITH FREQUENTLY TESTED
1000+ PRACTICE QUESTIONS AND STUDY GUIDE / EXPERT
VERIFIED FOR GUARANTEED PASS/ALREADY GRADED A+
BEST DOCUMENT FOR EXAM PREP
An extraction pump is not a required auxiliary component on a ____.
1. condensing steam turbine
2. non-condensing steam turbine
3. diesel engine
4. compressor
5. reciprocating engine
2. non-condensing steam turbine
When installing a it must be sized to prevent the boiler pressure rising 6%
above
the MAWP of the boiler.
1. check valve
2. boiler safety valve(s)
3. seal
4. try lever
5. low-water cut off
2. boiler safety valve(s)
,Two of the primary methods of include the sulphite and sulphate process
1. attemperator
2. chemical pulping
3. chemical evaporating
4. corrosion prevention
5. cooking liquor
2. chemical pulping
Crystallization may occur in situations where the rises above the upper
concentration limit at the lower temperature.
1. solutions lithium bromide concentration
2. solutions freon concentration
3. solutions water concentration
4. solutions air concentration
5. solutions salt concentration
5. solutions salt concentration
,The lifting capacity of the should always be verified before attempting a lift.
1. slings
2. pallet
3. lifted object
4. ratchet
5. bearings
1. slings
____ is a measure of a lubricating oils ability to support various loads.
1. Viscosity
2. Flash Point
3. Fire Point
4. Pour Point
5. Neutralization Number
1. Viscosity
, During design calculations is the absolute pressure expected at the pump
suction.
1. net positive suction head available
2. net positive suction head
3. net positive suction head required
4. net positive discharge head
5. net positive discharge head available
3. net positive suction head required
Which of the following affect the total heat loss from a building:
1. Radiation
2. Convection
3. Conduction
4. All of the above
4. All of the above
350 to 490 kPa is that typically operating pressure range of ____.
1. potable water systems
2. building water systems
3. municipal water distribution systems
4. well water systems
5. potable water systems
3. municipal water distribution systems
