www.stuvia.com/user/AcademicACHIEVER
Elevator Mechanic Final Exam Questions and
Answers With Expert Explanation (2026/2027
Update) | Complete A+ Guide
This Document Contains:
❖Elevator Mechanic Final Exam
❖Questions and Answers With Expert Explanation
❖Verified (2026/2027 Update)
❖100% Guaranteed Pass
❖Complete A+ Guide
Final Exam Elevator
,www.stuvia.com/user/AcademicACHIEVER
wrench used for rail installation correct answers pud wrench
The minimum clearance form the floor to the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2" correct answer a. 80"
what should you be aware of when removing a cab for replacement?
a. The weight that is to be removed from the ceiling.
b. The original weight and counterbalancing.
c. How much the cab was out of square.
d. Cover the panels so they do not get banged up. correct answer b. The
original weight and counterbalancing.
When fans are used on modernization jobs for exhausting fumes, what
statement is correct?
a. They're to keep you cool, not for exhausting fumes.
b. They should direct the fumes into the hoistway.
c. They should direct the fumes into the pit.
d. They should direct the fumes to the outside. correct answer d. They
should direct the fumes to the outside.
The star symbol is used on the COP for what?
a. To show where the floor buttons are located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location. correct answer b. To designate the
main floor.
Using a laminate stop strip against the fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the blade.
c. Keeps the laminate from slipping under the fence.
d. Keeps the laminate from going over the fence. correct answerc. Keeps
the laminate from slipping under the fence.
The contact adhesives must be ________ before final bonding:
a. 85 degrees
b. Dry
, www.stuvia.com/user/AcademicACHIEVER
c. Wet to touch
d. Cold correct answer b. Dry
What is the most important piece of equipment you have when using a
power saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square correct answer b. safety glasses
When using a circular saw, which of the following is correct?
a. Never start the cut until the blade is turning full RPM
b. The base is not adjustable for cutting depth
c. Circular saw blades range from 10 to 16 inches
d. Remove the retractable guard before cutting correct answer a. Never
start the cut until the blade is turning full RPM
What is used to make crosscuts on a table saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade correct answer c. Miter saw
When making crosscuts with a radial arm saw which statement is
correct?
a. Push the wood slowly into the blade.
b. Restrain the blade from moving too fast.
c. Rotate and lock the blade parallel to the guide.
d. Adjust the blade 1/4" above to cutting surface correct answer b.
Restrain the blade from moving too fast
What are the two things a compound mitre saw does best at the same
time?
a. moving it around and setting it up is fast.
b. You can cut left and right at the same time.
c. Tilting the blade 45 degrees and pivoting the table 45 degrees gives
you a 90 degree square cut.
d. bevel and mitre cuts can be made at the same time correct answer d.
bevel and mitre cuts can be made at the same time
Why do we use laminated glass in the walls of glass elevator cabs?
Elevator Mechanic Final Exam Questions and
Answers With Expert Explanation (2026/2027
Update) | Complete A+ Guide
This Document Contains:
❖Elevator Mechanic Final Exam
❖Questions and Answers With Expert Explanation
❖Verified (2026/2027 Update)
❖100% Guaranteed Pass
❖Complete A+ Guide
Final Exam Elevator
,www.stuvia.com/user/AcademicACHIEVER
wrench used for rail installation correct answers pud wrench
The minimum clearance form the floor to the suspended ceiling is:
a. 80"
b. 96"
c. 7'3"
d. 8'2" correct answer a. 80"
what should you be aware of when removing a cab for replacement?
a. The weight that is to be removed from the ceiling.
b. The original weight and counterbalancing.
c. How much the cab was out of square.
d. Cover the panels so they do not get banged up. correct answer b. The
original weight and counterbalancing.
When fans are used on modernization jobs for exhausting fumes, what
statement is correct?
a. They're to keep you cool, not for exhausting fumes.
b. They should direct the fumes into the hoistway.
c. They should direct the fumes into the pit.
d. They should direct the fumes to the outside. correct answer d. They
should direct the fumes to the outside.
The star symbol is used on the COP for what?
a. To show where the floor buttons are located.
b. To designate the main floor.
c. To make the door buttons stand out.
d. To show the alarm bell location. correct answer b. To designate the
main floor.
Using a laminate stop strip against the fence on a table saw:
a. Keeps the laminate straight to the blade.
b. Keeps the laminate from lifting off the blade.
c. Keeps the laminate from slipping under the fence.
d. Keeps the laminate from going over the fence. correct answerc. Keeps
the laminate from slipping under the fence.
The contact adhesives must be ________ before final bonding:
a. 85 degrees
b. Dry
, www.stuvia.com/user/AcademicACHIEVER
c. Wet to touch
d. Cold correct answer b. Dry
What is the most important piece of equipment you have when using a
power saw?
a. Combination blade
b. Safety glasses
c. Wood rule
d. Framing square correct answer b. safety glasses
When using a circular saw, which of the following is correct?
a. Never start the cut until the blade is turning full RPM
b. The base is not adjustable for cutting depth
c. Circular saw blades range from 10 to 16 inches
d. Remove the retractable guard before cutting correct answer a. Never
start the cut until the blade is turning full RPM
What is used to make crosscuts on a table saw?
a. Push stick
b. Rip fence
c. Miter gauge
d. Larger Blade correct answer c. Miter saw
When making crosscuts with a radial arm saw which statement is
correct?
a. Push the wood slowly into the blade.
b. Restrain the blade from moving too fast.
c. Rotate and lock the blade parallel to the guide.
d. Adjust the blade 1/4" above to cutting surface correct answer b.
Restrain the blade from moving too fast
What are the two things a compound mitre saw does best at the same
time?
a. moving it around and setting it up is fast.
b. You can cut left and right at the same time.
c. Tilting the blade 45 degrees and pivoting the table 45 degrees gives
you a 90 degree square cut.
d. bevel and mitre cuts can be made at the same time correct answer d.
bevel and mitre cuts can be made at the same time
Why do we use laminated glass in the walls of glass elevator cabs?
