CMPT 130 FINAL EXAM ALL POSSIBLE
QUESTIONS AND ANSWERS PROF BRIAN
FRASER SIMON FRASER UNIVERSITY
EXAMINATION TEST 2026 QUESTIONS
WITH SOLUTIONS GRADED A+
⩥ The purpose of cutting lubricant in most drilling ops is to increase the.
Answer: Drilling speed and drill bit life
⩥ Minimum protection using a bench grinder. Answer: eye and face
protection
⩥ what condition would prevent an operator from applying power to a
hoist or other powered lifting device. Answer: an AF Form 979
⩥ most common type of lifting sling. Answer: wire rope
⩥ the enunciators displayed on the fluke 8025 series multimeter are used
to distinguish among. Answer: ohms, kilohm, and megohms
⩥ 2 operational modes of the Fluke 8025. Answer: range and hold
,⩥ the steering system on the MHU 141/ M trailer has a turning radius of
how many inches. Answer: 200
⩥ When the MHU 141 trailer is loaded or towed with the hinged deck
panels open, what must be done?. Answer: the deck supports must be
properly positioned and locked in place with quick release pins
⩥ Max load capacity of the MHU 110/ M trailer. Answer: 15,000
⩥ the parking brake on the MHU 110/ M is applied by. Answer: pulling
either one of two hand levers located on each side of the front of trailer
⩥ how many openings are on the deck of the MHU- 226 trailer. Answer:
3
⩥ what type of steering aids the MHU- 226. Answer: four wheeled
double ackerman
⩥ After 463L pallets are positioned on a rollerized trailer, what can you
use to secure the pallets. Answer: MB-1 chain assemblies and or tie
down straps
⩥ what kind of movements supports on base activities to or from the
flightline. Answer: operational
,⩥ what munitions item is not loaded into transport modules by
munitions personnel. Answer: 20 mm
⩥ what transport module used for decoy munitions has a max capacity
of 30 magazines. Answer: ALE- 50
⩥ How often should the positive locking devices on the doors of
munitions transport modules be checked. Answer: after loading,
unloading and periodically between stops
⩥ the purpose of the transport beam beneath the lift arm assemblies on
the MJ- 1 series lift truck is to. Answer: provide added support and to
relieve hydraulic pressure from the lift arms when carrying loads for
long distances
⩥ Lifting capacity of the MJ 1 series lift truck. Answer: 3,000
⩥ Lifting capacity of MHU 83 lift truck. Answer: 7,000
⩥ When using fork adapters on MHU 83 series lift truck. Answer: it
reduces lifting capacity by 1,000
, ⩥ What happens when you release the accelerator pedal on a vehicle
driven with a hydrostatic transmission. Answer: the unit coasts to a stop
very quickly
⩥ what is the primary drawback to using the hydraulic hand pump to
build hydraulic pressure on the MHU 83 lift truck. Answer: extremely
slow way to build hydraulic pressure
⩥ How is the yaw positioning from the cradle or boom controls of an MJ
1 lift truck adjusted. Answer: Manually
⩥ what category are Air Force air compressors classified?. Answer: high
or low pressure
⩥ what is the purpose behind good operator maintenance of all assigned
vehicles. Answer: maintain vehicle serviceability at reduced cost
⩥ max amount thee MB 4 aircraft towing tractor can tow. Answer:
140,000
⩥ pintle safety locking pins must remain attached to the pintle assembly.
Answer: to prevent an insecure pin from coming out and getting lost
⩥ what gear should a tractor with automatic transmission while going
downhill. Answer: low
QUESTIONS AND ANSWERS PROF BRIAN
FRASER SIMON FRASER UNIVERSITY
EXAMINATION TEST 2026 QUESTIONS
WITH SOLUTIONS GRADED A+
⩥ The purpose of cutting lubricant in most drilling ops is to increase the.
Answer: Drilling speed and drill bit life
⩥ Minimum protection using a bench grinder. Answer: eye and face
protection
⩥ what condition would prevent an operator from applying power to a
hoist or other powered lifting device. Answer: an AF Form 979
⩥ most common type of lifting sling. Answer: wire rope
⩥ the enunciators displayed on the fluke 8025 series multimeter are used
to distinguish among. Answer: ohms, kilohm, and megohms
⩥ 2 operational modes of the Fluke 8025. Answer: range and hold
,⩥ the steering system on the MHU 141/ M trailer has a turning radius of
how many inches. Answer: 200
⩥ When the MHU 141 trailer is loaded or towed with the hinged deck
panels open, what must be done?. Answer: the deck supports must be
properly positioned and locked in place with quick release pins
⩥ Max load capacity of the MHU 110/ M trailer. Answer: 15,000
⩥ the parking brake on the MHU 110/ M is applied by. Answer: pulling
either one of two hand levers located on each side of the front of trailer
⩥ how many openings are on the deck of the MHU- 226 trailer. Answer:
3
⩥ what type of steering aids the MHU- 226. Answer: four wheeled
double ackerman
⩥ After 463L pallets are positioned on a rollerized trailer, what can you
use to secure the pallets. Answer: MB-1 chain assemblies and or tie
down straps
⩥ what kind of movements supports on base activities to or from the
flightline. Answer: operational
,⩥ what munitions item is not loaded into transport modules by
munitions personnel. Answer: 20 mm
⩥ what transport module used for decoy munitions has a max capacity
of 30 magazines. Answer: ALE- 50
⩥ How often should the positive locking devices on the doors of
munitions transport modules be checked. Answer: after loading,
unloading and periodically between stops
⩥ the purpose of the transport beam beneath the lift arm assemblies on
the MJ- 1 series lift truck is to. Answer: provide added support and to
relieve hydraulic pressure from the lift arms when carrying loads for
long distances
⩥ Lifting capacity of the MJ 1 series lift truck. Answer: 3,000
⩥ Lifting capacity of MHU 83 lift truck. Answer: 7,000
⩥ When using fork adapters on MHU 83 series lift truck. Answer: it
reduces lifting capacity by 1,000
, ⩥ What happens when you release the accelerator pedal on a vehicle
driven with a hydrostatic transmission. Answer: the unit coasts to a stop
very quickly
⩥ what is the primary drawback to using the hydraulic hand pump to
build hydraulic pressure on the MHU 83 lift truck. Answer: extremely
slow way to build hydraulic pressure
⩥ How is the yaw positioning from the cradle or boom controls of an MJ
1 lift truck adjusted. Answer: Manually
⩥ what category are Air Force air compressors classified?. Answer: high
or low pressure
⩥ what is the purpose behind good operator maintenance of all assigned
vehicles. Answer: maintain vehicle serviceability at reduced cost
⩥ max amount thee MB 4 aircraft towing tractor can tow. Answer:
140,000
⩥ pintle safety locking pins must remain attached to the pintle assembly.
Answer: to prevent an insecure pin from coming out and getting lost
⩥ what gear should a tractor with automatic transmission while going
downhill. Answer: low
