Adhesive Anchor Training Exam Questions & Answers | Latest
Already Graded A+ |Questions with Correct Answers 2026
latest update!!
1. Minimum anchor spacing and edge distance, as well as minimum
member thickness, must comply with the values given -
(ANSWERS)In the products ICC-ES Report
2. The registered design professional in responsible charge and the
engineers of record involved in the design of the project are permitted
to act as the - (ANSWERS)Approved Agency
3. If reinforcing bars are encountered during drilling the correct action
would be - (ANSWERS)Consulting with the EOR
4. For adhesive anchors, the characteristics bond stresses and suitability
for structural applications are established by testing in accordance with
- (ANSWERS)ACI 355.4
5. Special inspections and tests shall be required for proposal work that is,
in the opinion of the building official, unusual in its nature, as such, but
not limited to - (ANSWERS)All of the above
6. ACI 355.4, qualification of post installed adhesive anchors in concrete,
is applicable to anchors with a specified minimum embedment depth of
,Adhesive Anchor Training Exam Questions & Answers | Latest
Already Graded A+ |Questions with Correct Answers 2026
latest update!!
- (ANSWERS)1 - 5/8 inches
7. Proof loads are usually determined as a - (ANSWERS)Percentage of
the anchor ultimate tensile strength
8. True or False: The contractor is permitted to employ the approved
agencies for special inspection where the contractor is also the owner of
the project? - (ANSWERS)True
9. The effective embedment depth, measure from the concrete surface to
the deepest point at which bond to the concrete is established is
identified as - (ANSWERS)h subscript(ef)
10. True or false: Powers PE1000+ epoxy adhesive are recognized for
use to resist short-term and long-term loads, including wind and
earthquake loads, subject to conditions of the ICC-ES Evaluation
report? - (ANSWERS)True
11. Short sections of anchor rods the have been burned or sawed are
indictive of: - (ANSWERS)Incorrect embedment
, Adhesive Anchor Training Exam Questions & Answers | Latest
Already Graded A+ |Questions with Correct Answers 2026
latest update!!
12. The elapsed time after mixing adhesive material components to
onset of significant chemical reaction as characterized by an increase in
viscosity is - (ANSWERS)Gel Time
13. Periodic and final inspection reports are required to be summited to
the - (ANSWERS)Building official and engineer or architect of record
14. Powers PE1000+ epoxy adhesive anchors must be installed in
accordance with? - (ANSWERS)The manufacturers published
installation instructions
15. ACI 355.4-11 qualification of post installed adhesive anchors in
concrete standard applies to anchors with diameter of 1/4in or larger
and an embedment depth not exceeding: - (ANSWERS)20d(a)
16. The( ) ensures that the components are well mixed so the adhesive
resin is activated by the hardener - (ANSWERS)Mixing Nozzle
17. The ICC-ES evaluation report for the powers 1000+ product
specifies that holes drilled in concrete be cleaned out by using? -
Already Graded A+ |Questions with Correct Answers 2026
latest update!!
1. Minimum anchor spacing and edge distance, as well as minimum
member thickness, must comply with the values given -
(ANSWERS)In the products ICC-ES Report
2. The registered design professional in responsible charge and the
engineers of record involved in the design of the project are permitted
to act as the - (ANSWERS)Approved Agency
3. If reinforcing bars are encountered during drilling the correct action
would be - (ANSWERS)Consulting with the EOR
4. For adhesive anchors, the characteristics bond stresses and suitability
for structural applications are established by testing in accordance with
- (ANSWERS)ACI 355.4
5. Special inspections and tests shall be required for proposal work that is,
in the opinion of the building official, unusual in its nature, as such, but
not limited to - (ANSWERS)All of the above
6. ACI 355.4, qualification of post installed adhesive anchors in concrete,
is applicable to anchors with a specified minimum embedment depth of
,Adhesive Anchor Training Exam Questions & Answers | Latest
Already Graded A+ |Questions with Correct Answers 2026
latest update!!
- (ANSWERS)1 - 5/8 inches
7. Proof loads are usually determined as a - (ANSWERS)Percentage of
the anchor ultimate tensile strength
8. True or False: The contractor is permitted to employ the approved
agencies for special inspection where the contractor is also the owner of
the project? - (ANSWERS)True
9. The effective embedment depth, measure from the concrete surface to
the deepest point at which bond to the concrete is established is
identified as - (ANSWERS)h subscript(ef)
10. True or false: Powers PE1000+ epoxy adhesive are recognized for
use to resist short-term and long-term loads, including wind and
earthquake loads, subject to conditions of the ICC-ES Evaluation
report? - (ANSWERS)True
11. Short sections of anchor rods the have been burned or sawed are
indictive of: - (ANSWERS)Incorrect embedment
, Adhesive Anchor Training Exam Questions & Answers | Latest
Already Graded A+ |Questions with Correct Answers 2026
latest update!!
12. The elapsed time after mixing adhesive material components to
onset of significant chemical reaction as characterized by an increase in
viscosity is - (ANSWERS)Gel Time
13. Periodic and final inspection reports are required to be summited to
the - (ANSWERS)Building official and engineer or architect of record
14. Powers PE1000+ epoxy adhesive anchors must be installed in
accordance with? - (ANSWERS)The manufacturers published
installation instructions
15. ACI 355.4-11 qualification of post installed adhesive anchors in
concrete standard applies to anchors with diameter of 1/4in or larger
and an embedment depth not exceeding: - (ANSWERS)20d(a)
16. The( ) ensures that the components are well mixed so the adhesive
resin is activated by the hardener - (ANSWERS)Mixing Nozzle
17. The ICC-ES evaluation report for the powers 1000+ product
specifies that holes drilled in concrete be cleaned out by using? -
