CMGT CAPSTONE EXAM 2 QUESTIONS
AND ANSWERS 2026 VERIFIED.
What is the commissioning process - ANS Ensuring that all MEP Systems are designed,
installed, tested, and documented optimally to meet owner requirements
What is the TAB process - ANS Measuring and adjusting the air and water flow rates in MEP
equipment to ensure they meet specs
What is IAQ - ANS Indoor Air Quality, The cleanliness of air inside of a building, managed by
ventilation and HVAC.
Ventilation vs Infiltration - ANS Ventilation is the controlled introduction of fresh air into a
building
Infiltration is the uncontrolled leakage of outside air into a building through gaps in the building
What is ohms law - ANS V=I*R
Current = Voltage / Resistance
Resistance = Voltage / Current
So it takes 1 volt to push 1 amp through 1 ohm of resistance to produce 1 watt
, Amperage - ANS Flow rate of electricity
Voltage - ANS The electrical potential difference "electrical pressure" between two points
that forces charge (electrons) to flow as a current through a circuit
Ampacity - ANS The maximum current, measured in ameperes, that a conductor or cable can
continuously carry without exceeding its safe temperature rating
Ohms - ANS Resistance in a circuit, measures how strongly a material opposes the flow of
electricity.
(longer wire has higher resistance)
(Wire with a larger cross-sectional area has a lower resistance)
Components of a circuit - ANS Power (source)
Conductors (path)
Load (item requiring the power)
What is the correct order of electrical distribution for the following components: circuit breaker,
outlet, panel, switchgear, subpanel, substation, transformer. - ANS Substation -> Switchgear -
> Panel -> Transformer -> panel -> 3 phase circuit breaker -> subpanel -> circuit breaker ->
outlets
Water Supply System - ANS Brings clean, potable water into the building from water mains or
wells.
Sanitary Waste System - ANS Removes wastewater and sewage from the building using
gravity through drain pipes.
Storm Water System - ANS Removes rainwater from roofs and surfaces.
AND ANSWERS 2026 VERIFIED.
What is the commissioning process - ANS Ensuring that all MEP Systems are designed,
installed, tested, and documented optimally to meet owner requirements
What is the TAB process - ANS Measuring and adjusting the air and water flow rates in MEP
equipment to ensure they meet specs
What is IAQ - ANS Indoor Air Quality, The cleanliness of air inside of a building, managed by
ventilation and HVAC.
Ventilation vs Infiltration - ANS Ventilation is the controlled introduction of fresh air into a
building
Infiltration is the uncontrolled leakage of outside air into a building through gaps in the building
What is ohms law - ANS V=I*R
Current = Voltage / Resistance
Resistance = Voltage / Current
So it takes 1 volt to push 1 amp through 1 ohm of resistance to produce 1 watt
, Amperage - ANS Flow rate of electricity
Voltage - ANS The electrical potential difference "electrical pressure" between two points
that forces charge (electrons) to flow as a current through a circuit
Ampacity - ANS The maximum current, measured in ameperes, that a conductor or cable can
continuously carry without exceeding its safe temperature rating
Ohms - ANS Resistance in a circuit, measures how strongly a material opposes the flow of
electricity.
(longer wire has higher resistance)
(Wire with a larger cross-sectional area has a lower resistance)
Components of a circuit - ANS Power (source)
Conductors (path)
Load (item requiring the power)
What is the correct order of electrical distribution for the following components: circuit breaker,
outlet, panel, switchgear, subpanel, substation, transformer. - ANS Substation -> Switchgear -
> Panel -> Transformer -> panel -> 3 phase circuit breaker -> subpanel -> circuit breaker ->
outlets
Water Supply System - ANS Brings clean, potable water into the building from water mains or
wells.
Sanitary Waste System - ANS Removes wastewater and sewage from the building using
gravity through drain pipes.
Storm Water System - ANS Removes rainwater from roofs and surfaces.
