WOODSHOP SAFETY TEST EXAM
STUDY GUIDE COMPLETE QUESTIONS
WITH CORRECT SOLUTIONS||100%
GUARANTEED PASS||UPDATED
2026/2027 SYLLABUS||A+
GRADED||<<RECENT VERSION>>
How high above the stock should the saw blade be - ANSWER ✓ 1/8"
When cutting large pieces of stock on the saw the helper should - ANSWER ✓
Support the stock at the table height only
To be safe cut freehand I the table saw - ANSWER ✓ Never
Any speak oak setups on the. Saw mist be inspected by - ANSWER ✓ Instructor
To be safely ripped without using a push stick,stock must not be narrower than -
ANSWER ✓ 6"
To stop a revolving saw blade it is best to - ANSWER ✓ Allow the revolving
blade to stop by itself
The chance of kickback is greatly reduced if - ANSWER ✓ The stock is longer
than it is wide
It is permissible for the operator to reach over the blade at certain times -
ANSWER ✓ Never
When you are through making your cuts you should - ANSWER ✓ Turn off the
machine and wait for the blade to stop
, Freehand sawing on the band saw should be attempted only - ANSWER ✓ When
the work to be sawed is rested flat on the table
Before starting a cut, should check the machine for - ANSWER ✓ All of these
When sawing sharp curves, one should - ANSWER ✓ All if these
If the band saw blade should break while the machine is in operation, the operator
should - ANSWER ✓ Stand Clear of the machine and turn off the power
When backing the saw blade out of a long cut - ANSWER ✓ Turning off the
machine and wait for the blade to come to a complete stop
I the scroll saw, it is the best to rotate the blade by hand first to see the see that -
ANSWER ✓ All of these
Drillpress work should be held - ANSWER ✓ With a pair of pliers
Whe. The drill begins to back through the work, you should - ANSWER ✓ Ease
up on the feed pressure
If the wood is seized by the still bit , one should carefully - ANSWER ✓ Stop the
machine and free the work
Using the correct speed on the drill press insured that - ANSWER ✓ All of the
above
By removing the chuck key before turning on the power, you will prevent -
ANSWER ✓ Both b and c will be prevented
After the cutter head has been securely fastened to the spindle - ANSWER ✓
Mekong sure that the spindle turns freely before turning on the machine
End grain of boards less than -- inches wide should my be shaped on the end
without a miter gauge or jig - ANSWER ✓ 10"
To determine the direction the cutter head to rotating one should - ANSWER ✓
Turn the machine on and off quickly and watch the knives come to a stop
STUDY GUIDE COMPLETE QUESTIONS
WITH CORRECT SOLUTIONS||100%
GUARANTEED PASS||UPDATED
2026/2027 SYLLABUS||A+
GRADED||<<RECENT VERSION>>
How high above the stock should the saw blade be - ANSWER ✓ 1/8"
When cutting large pieces of stock on the saw the helper should - ANSWER ✓
Support the stock at the table height only
To be safe cut freehand I the table saw - ANSWER ✓ Never
Any speak oak setups on the. Saw mist be inspected by - ANSWER ✓ Instructor
To be safely ripped without using a push stick,stock must not be narrower than -
ANSWER ✓ 6"
To stop a revolving saw blade it is best to - ANSWER ✓ Allow the revolving
blade to stop by itself
The chance of kickback is greatly reduced if - ANSWER ✓ The stock is longer
than it is wide
It is permissible for the operator to reach over the blade at certain times -
ANSWER ✓ Never
When you are through making your cuts you should - ANSWER ✓ Turn off the
machine and wait for the blade to stop
, Freehand sawing on the band saw should be attempted only - ANSWER ✓ When
the work to be sawed is rested flat on the table
Before starting a cut, should check the machine for - ANSWER ✓ All of these
When sawing sharp curves, one should - ANSWER ✓ All if these
If the band saw blade should break while the machine is in operation, the operator
should - ANSWER ✓ Stand Clear of the machine and turn off the power
When backing the saw blade out of a long cut - ANSWER ✓ Turning off the
machine and wait for the blade to come to a complete stop
I the scroll saw, it is the best to rotate the blade by hand first to see the see that -
ANSWER ✓ All of these
Drillpress work should be held - ANSWER ✓ With a pair of pliers
Whe. The drill begins to back through the work, you should - ANSWER ✓ Ease
up on the feed pressure
If the wood is seized by the still bit , one should carefully - ANSWER ✓ Stop the
machine and free the work
Using the correct speed on the drill press insured that - ANSWER ✓ All of the
above
By removing the chuck key before turning on the power, you will prevent -
ANSWER ✓ Both b and c will be prevented
After the cutter head has been securely fastened to the spindle - ANSWER ✓
Mekong sure that the spindle turns freely before turning on the machine
End grain of boards less than -- inches wide should my be shaped on the end
without a miter gauge or jig - ANSWER ✓ 10"
To determine the direction the cutter head to rotating one should - ANSWER ✓
Turn the machine on and off quickly and watch the knives come to a stop
