Page 1 of 103
Florida Sheet Metal Contractor Licensing Exam ACTUAL EXAM
COMPLETE QUESTIONS AND CORRECT ANSWERS LATEST
UPDATE THIS YEAR
Florida Sheet Metal Contractor Licensing Exam
ACTUAL EXAM COVERAGE (CORE TOPICS)
1. Sheet Metal Materials
• Galvanized steel, stainless steel, aluminum
• Gauge thickness and application limits
• Corrosion resistance and environmental suitability
2. HVAC Sheet Metal Fabrication
• Duct design (rectangular, round, spiral)
• Airflow principles and sizing
• Fittings: elbows, transitions, reducers, takeoffs
3. Layout & Blueprint Reading
• Reading mechanical plans and shop drawings
• Scale interpretation and dimensions
• Isometric duct layout understanding
4. Installation Practices
• Hanging and supporting duct systems
• Fasteners, seams, joints (S-cleat, drive cleat, slip joint)
• Sealing and insulation requirements
5. Florida Building Code Knowledge
• Mechanical code compliance
• Fire and smoke dampers
• Energy efficiency requirements
6. Tools & Equipment
• Shears, brakes, seamers, plasma cutters
• Measuring tools and calibration
• Safety equipment
, Page 2 of 103
7. Air Distribution Systems
• Static pressure basics
• CFM calculations
• Leakage prevention
8. Safety & OSHA Standards
• Fall protection
• Ladder safety
• Sheet metal handling hazards
1.
What is the primary purpose of sheet metal ductwork in HVAC systems?
A. Increase building weight
B. Transport conditioned air efficiently throughout a structure
C. Store electrical wiring
D. Reduce insulation needs
Answer: B
2.
Which material is most commonly used for general HVAC duct construction?
A. Copper
B. Galvanized steel
, Page 3 of 103
C. Lead
D. Cast iron
Answer: B
3.
What is the primary function of a slip joint in duct installation?
A. Increase airflow resistance
B. Allow connection and slight movement between duct sections
C. Seal electrical circuits
D. Reduce duct size permanently
Answer: B
4.
What is the main purpose of duct insulation?
A. Increase airflow speed
B. Prevent heat loss or gain and reduce condensation
, Page 4 of 103
C. Strengthen duct structure
D. Increase air leakage
Answer: B
5.
What does CFM represent in HVAC systems?
A. Cooling force measurement
B. Cubic feet of air per minute airflow rate
C. Compressor fuel measure
D. Condensation flow metric
Answer: B
6.
What is the primary purpose of a takeoff fitting in ductwork?
A. Block airflow
B. Branch air from main duct into smaller duct lines
Florida Sheet Metal Contractor Licensing Exam ACTUAL EXAM
COMPLETE QUESTIONS AND CORRECT ANSWERS LATEST
UPDATE THIS YEAR
Florida Sheet Metal Contractor Licensing Exam
ACTUAL EXAM COVERAGE (CORE TOPICS)
1. Sheet Metal Materials
• Galvanized steel, stainless steel, aluminum
• Gauge thickness and application limits
• Corrosion resistance and environmental suitability
2. HVAC Sheet Metal Fabrication
• Duct design (rectangular, round, spiral)
• Airflow principles and sizing
• Fittings: elbows, transitions, reducers, takeoffs
3. Layout & Blueprint Reading
• Reading mechanical plans and shop drawings
• Scale interpretation and dimensions
• Isometric duct layout understanding
4. Installation Practices
• Hanging and supporting duct systems
• Fasteners, seams, joints (S-cleat, drive cleat, slip joint)
• Sealing and insulation requirements
5. Florida Building Code Knowledge
• Mechanical code compliance
• Fire and smoke dampers
• Energy efficiency requirements
6. Tools & Equipment
• Shears, brakes, seamers, plasma cutters
• Measuring tools and calibration
• Safety equipment
, Page 2 of 103
7. Air Distribution Systems
• Static pressure basics
• CFM calculations
• Leakage prevention
8. Safety & OSHA Standards
• Fall protection
• Ladder safety
• Sheet metal handling hazards
1.
What is the primary purpose of sheet metal ductwork in HVAC systems?
A. Increase building weight
B. Transport conditioned air efficiently throughout a structure
C. Store electrical wiring
D. Reduce insulation needs
Answer: B
2.
Which material is most commonly used for general HVAC duct construction?
A. Copper
B. Galvanized steel
, Page 3 of 103
C. Lead
D. Cast iron
Answer: B
3.
What is the primary function of a slip joint in duct installation?
A. Increase airflow resistance
B. Allow connection and slight movement between duct sections
C. Seal electrical circuits
D. Reduce duct size permanently
Answer: B
4.
What is the main purpose of duct insulation?
A. Increase airflow speed
B. Prevent heat loss or gain and reduce condensation
, Page 4 of 103
C. Strengthen duct structure
D. Increase air leakage
Answer: B
5.
What does CFM represent in HVAC systems?
A. Cooling force measurement
B. Cubic feet of air per minute airflow rate
C. Compressor fuel measure
D. Condensation flow metric
Answer: B
6.
What is the primary purpose of a takeoff fitting in ductwork?
A. Block airflow
B. Branch air from main duct into smaller duct lines
