1|Page
ICC Reinforced Concrete 2026/2027 || Most Recent
Exam Actual Complete Real Verified Exam Questions
And Correct Answers (Verified Answers) Already
Graded A+ | Guaranteed Success!! || Newest Exam!!!
ACI 318 - Answer-Governs structural concrete design,
construction, inspection and acceptance
Load Path - Answer-A continuous system of structural
elements that transfer an applied load to the supporting
soil.
Which of the following publications are most useful for a
Special Inspector? - Answer-ACI 318
A_____ is a horizontal member that transfers loads
laterally. - Answer-Beam
Plain concrete refers to: - Answer-Concrete with less than
minimum amount of reinforcement
A beam is primarily subject to ____ whole a column is
primarily subject to _______. - Answer-A. Shear, Flexure
,2|Page
B. Compression, flexure C. Flexure, compression D.
Compression, shear
Answer C. Flexure, Compression
A beam is primarily subject to compression while a column
is primarily subject to shear. True or False - Answer-False.
Beam is subject to Flexure, column is subject to
compression.
The best place to look up definitions in ACI 318-14 is: -
Answer-Chapter 2
Foundations cast at the same elevation as the soil grade
are known as: - Answer-Shallow
What causes concrete to set and become hardened? -
Answer-Hydration
,3|Page
Cement forming chemical bonds with water molecules,
which sets things in motion to become an extremely
hardened material. - Answer-Hydration Process
In general, how long does it take for concrete to move
from a plastic state to a hardened state, depending on
weather and admixtures? - Answer-30 minutes to 5 hours
Many project specifications consider concrete rejectable
after it has bee what? - Answer-Batched for 90 minutes
Hydration is "exothermic", meaning what? - Answer-It
produces heat.
What are pozzolans? - Answer-siliceous or
siliceous/aluminous materials which have little to no
cementitious value alone; react with lime and water to
form a product similar to C-S-H.
Aggregates not conforming to ASTM C33 or C330 must be
what? - Answer-Shown by test or actual service to
produce concrete of adequate strength and durability and
approved by the building official.
, 4|Page
Aggregates make up what percent of concrete? - Answer-
60-80%
Pumice and tuff are considered what kind of aggregate? -
Answer-Lightweight
When pouring a structural concrete slab over a metal
deck, what kind of concrete is necessary? - Answer-
Lightweight
ASTM C33 pertains to what? - Answer-A: Water B: Steel
Fiber Reinforcement C: Calcium Chloride D: Normalweight
Aggregate E: None of the Above
Answer D: Normalweight Aggregate
ASTM C33 is divided into 2 Categories. What are they? -
Answer-Coarse & Fine
What is honeycomb? - Answer-Visible voids in the
concrete
ICC Reinforced Concrete 2026/2027 || Most Recent
Exam Actual Complete Real Verified Exam Questions
And Correct Answers (Verified Answers) Already
Graded A+ | Guaranteed Success!! || Newest Exam!!!
ACI 318 - Answer-Governs structural concrete design,
construction, inspection and acceptance
Load Path - Answer-A continuous system of structural
elements that transfer an applied load to the supporting
soil.
Which of the following publications are most useful for a
Special Inspector? - Answer-ACI 318
A_____ is a horizontal member that transfers loads
laterally. - Answer-Beam
Plain concrete refers to: - Answer-Concrete with less than
minimum amount of reinforcement
A beam is primarily subject to ____ whole a column is
primarily subject to _______. - Answer-A. Shear, Flexure
,2|Page
B. Compression, flexure C. Flexure, compression D.
Compression, shear
Answer C. Flexure, Compression
A beam is primarily subject to compression while a column
is primarily subject to shear. True or False - Answer-False.
Beam is subject to Flexure, column is subject to
compression.
The best place to look up definitions in ACI 318-14 is: -
Answer-Chapter 2
Foundations cast at the same elevation as the soil grade
are known as: - Answer-Shallow
What causes concrete to set and become hardened? -
Answer-Hydration
,3|Page
Cement forming chemical bonds with water molecules,
which sets things in motion to become an extremely
hardened material. - Answer-Hydration Process
In general, how long does it take for concrete to move
from a plastic state to a hardened state, depending on
weather and admixtures? - Answer-30 minutes to 5 hours
Many project specifications consider concrete rejectable
after it has bee what? - Answer-Batched for 90 minutes
Hydration is "exothermic", meaning what? - Answer-It
produces heat.
What are pozzolans? - Answer-siliceous or
siliceous/aluminous materials which have little to no
cementitious value alone; react with lime and water to
form a product similar to C-S-H.
Aggregates not conforming to ASTM C33 or C330 must be
what? - Answer-Shown by test or actual service to
produce concrete of adequate strength and durability and
approved by the building official.
, 4|Page
Aggregates make up what percent of concrete? - Answer-
60-80%
Pumice and tuff are considered what kind of aggregate? -
Answer-Lightweight
When pouring a structural concrete slab over a metal
deck, what kind of concrete is necessary? - Answer-
Lightweight
ASTM C33 pertains to what? - Answer-A: Water B: Steel
Fiber Reinforcement C: Calcium Chloride D: Normalweight
Aggregate E: None of the Above
Answer D: Normalweight Aggregate
ASTM C33 is divided into 2 Categories. What are they? -
Answer-Coarse & Fine
What is honeycomb? - Answer-Visible voids in the
concrete
