FANUC FLASHCARDS LAB FINAL PAPER
2026 PRACTICE SOLUTION FULL
QUESTIONS WITH ANSWERS GRADED A+
⩥ If the selected speed is too slow, the robot will never reach the
selected speed and its movement will appear jerky.
True
False. Answer: False
⩥ There is no rule of thumb regarding how close a robot can or should
come to the programmed position or how much of an arc needs to be
created when traveling to the position.
True
False. Answer: True
⩥ The speed unit type can be changed by highlighting the speed and
pressing F4 [Choice].
True
False. Answer: True
,⩥ A termination of CNT100 is slower than a CNT with a lower number.
True
False. Answer: False
⩥ Any movement settings applied to point A define ___.
the preceding movement
the following movement
all movements before point A
all movements after point A. Answer: the preceding movement
⩥ Movement types are represented by single letters in the movement
line: J for joint, L for linear, C for circular, and A for ___.
actual
axial
angular
circle arc. Answer: circle arc
⩥ ___ a robot's movements will result in smoother robot operation, more
accurate positioning, and faster task completion.
,Accelerating
Slowing down
Stepping
Terminating. Answer: Slowing down
⩥ The ___ of a point describes how a robot ends one movement and
continues to the next.
position ID
movement type
termination
speed. Answer: termination
⩥ A setting of ___ is nearly the same as a fine termination.
CNT1
CNT25
CNT50
CNT100. Answer: CNT1
⩥ ___ unit(s) of speed is/are available to use with all movement types.
, No
Only one
All
Not all. Answer: Not all
⩥ There are two types of terminations: fine and ___.
smooth
contact
continuous
cornered. Answer: continuous
⩥ A movement using continuous termination is ___ than a movement
using fine termination.
more precise
jerkier
faster
slower. Answer: faster
2026 PRACTICE SOLUTION FULL
QUESTIONS WITH ANSWERS GRADED A+
⩥ If the selected speed is too slow, the robot will never reach the
selected speed and its movement will appear jerky.
True
False. Answer: False
⩥ There is no rule of thumb regarding how close a robot can or should
come to the programmed position or how much of an arc needs to be
created when traveling to the position.
True
False. Answer: True
⩥ The speed unit type can be changed by highlighting the speed and
pressing F4 [Choice].
True
False. Answer: True
,⩥ A termination of CNT100 is slower than a CNT with a lower number.
True
False. Answer: False
⩥ Any movement settings applied to point A define ___.
the preceding movement
the following movement
all movements before point A
all movements after point A. Answer: the preceding movement
⩥ Movement types are represented by single letters in the movement
line: J for joint, L for linear, C for circular, and A for ___.
actual
axial
angular
circle arc. Answer: circle arc
⩥ ___ a robot's movements will result in smoother robot operation, more
accurate positioning, and faster task completion.
,Accelerating
Slowing down
Stepping
Terminating. Answer: Slowing down
⩥ The ___ of a point describes how a robot ends one movement and
continues to the next.
position ID
movement type
termination
speed. Answer: termination
⩥ A setting of ___ is nearly the same as a fine termination.
CNT1
CNT25
CNT50
CNT100. Answer: CNT1
⩥ ___ unit(s) of speed is/are available to use with all movement types.
, No
Only one
All
Not all. Answer: Not all
⩥ There are two types of terminations: fine and ___.
smooth
contact
continuous
cornered. Answer: continuous
⩥ A movement using continuous termination is ___ than a movement
using fine termination.
more precise
jerkier
faster
slower. Answer: faster
