OSHA 10 TEST | COMPLETE STUDY GUIDE
2026/2027 | VERIFIED ANSWERS | 100%
CORRECT | GRADED A+ | PASS
QUARANTEED | BRAND NEW
OSHA's mission - ANSWER To ensure a safe and healthy workplace for every
working man and woman in the nation
General Duty Clause requires from employees? - ANSWER Comply with
occupational safety and health standards
Required to be posted in a conspicuous location - ANSWER OSHA 300a year
summary of workplace injuries and illnesses
Report of a workplace fatality - ANSWER 8 hours for a fatality, Colin 24 hours
for hospitalization, amputation, or eyesight
OSHA priority inspections - ANSWER Imminent danger
Violations of an electrical in nature are considered to be what -
ANSWER Serious
When approached by an OSHA inspection officer, what must happen first -
ANSWER Presentation of credentials
,Power delivery employees fall protection - ANSWER 4 feet above ground on
poles Towers or similar structures this is a vertical rule
What is OSHA's phone number - ANSWER +1-800-321- OSHA
Free Fall distances - ANSWER 6 feet free fall comma three and a half feet
deceleration 9 and a half feet total
Ladder angle equation - ANSWER 4 feet of height 1 foot of distance 3 feet of
handrail
Positioning device system requirements - ANSWER Anchorage of at least three
thousand pounds, Free Fall no more than 2 feet
Electrocution hazards be safe acronym - ANSWER Burns, electrocution, shock
Arc, fire, explosions
What electrocution Hazard exists for the system neutral - ANSWER They carry
return path current
What are the types of machine guarding discussed in 29 CFR 1910.212? -
ANSWER Barrier guards, two-hand tripping devices, electronic safety devices
What are surface grinders and cutting-off machines as described in 29 CFR
1910.215(b)(5)? - ANSWER The maximum angular exposure of the grinding
wheel periphery and sides for safety guards used on cutting-off and surface
,grinding machines, which employ the wheel periphery, shall not exceed 150
degrees. This exposure shall begin at a point not less than 15 degrees below the
horizontal plane of the wheel spindle.
What is the "Ring Test" as described in 29 CFR 1910.215(d)(1) and 215(d)(1)(i)? -
ANSWER Wheels should be tapped gently with a light nonmetallic implement,
and if the sound cracked (dead) they shall not be used.
What are the requirements for guarding horizontal shafting seven feet or less from
the floor according to 29 CFR 1910.219(c)(2)(i)? - ANSWER Shall be protected
by a stationary casing enclosing shafting completely or by a trough enclosing sides
and top or sides and bottom of shafting as location requires.
What are the requirements for shaft couplings according to 29 CFR
1910.219(i)(2)? - ANSWER Shall be so constructed as to present no hazards
from bolts, nuts, setscrews, or revolving surfaces. Bolts, nuts, and setscrews will be
permitted when covered with safety sleeves or where they are used parallel and
countersunk with shafting.
According to 29 CFR 1910.219(p)(7), what are the requirements for the person or
oiler when lubricating machinery? - ANSWER Must wear tight-fitting clothing
and machinery shall be oiled when not in motion (if possible).
Question 1: Is Adrian Smith, one of 3 employees of ABC Landscaping, covered by
OSHA? - ANSWER A. Yes
Question 2: Is Taylor Dell, an accountant in business for herself, covered by
OSHA? - ANSWER B. No
, Question 3: Is Rob Jones, one of 10 carpenters working for Woody, Inc., covered
by OSHA? - ANSWER A. Yes
Question 4: Why was OSHA necessary?
A. Workplace injuries, illnesses and death were increasing
B. No uniform or Comprehensive law existed to protect against workplace hazards
C. None of the Above
D. Both A and B - ANSWER D. Both A and B
Question 5: What is OSHA's mission?
A. To save lives
B. To prevent injuries
C. Protect the health of America's workers
D. All the answers are correct - ANSWER D. All the answers are correct
Question 6: Why is this training important?
A. You'll know your rights if there are hazards in your workplace.
B. You'll know where to get help.
C. You'll know if your employer is complying with OSHA standards.
D. All of the answers are correct - ANSWER D. All of the answers are correct
Question 1: What are some of the things you might find on an SDS?
A. Chemical Name
B. You'll know where to get help
2026/2027 | VERIFIED ANSWERS | 100%
CORRECT | GRADED A+ | PASS
QUARANTEED | BRAND NEW
OSHA's mission - ANSWER To ensure a safe and healthy workplace for every
working man and woman in the nation
General Duty Clause requires from employees? - ANSWER Comply with
occupational safety and health standards
Required to be posted in a conspicuous location - ANSWER OSHA 300a year
summary of workplace injuries and illnesses
Report of a workplace fatality - ANSWER 8 hours for a fatality, Colin 24 hours
for hospitalization, amputation, or eyesight
OSHA priority inspections - ANSWER Imminent danger
Violations of an electrical in nature are considered to be what -
ANSWER Serious
When approached by an OSHA inspection officer, what must happen first -
ANSWER Presentation of credentials
,Power delivery employees fall protection - ANSWER 4 feet above ground on
poles Towers or similar structures this is a vertical rule
What is OSHA's phone number - ANSWER +1-800-321- OSHA
Free Fall distances - ANSWER 6 feet free fall comma three and a half feet
deceleration 9 and a half feet total
Ladder angle equation - ANSWER 4 feet of height 1 foot of distance 3 feet of
handrail
Positioning device system requirements - ANSWER Anchorage of at least three
thousand pounds, Free Fall no more than 2 feet
Electrocution hazards be safe acronym - ANSWER Burns, electrocution, shock
Arc, fire, explosions
What electrocution Hazard exists for the system neutral - ANSWER They carry
return path current
What are the types of machine guarding discussed in 29 CFR 1910.212? -
ANSWER Barrier guards, two-hand tripping devices, electronic safety devices
What are surface grinders and cutting-off machines as described in 29 CFR
1910.215(b)(5)? - ANSWER The maximum angular exposure of the grinding
wheel periphery and sides for safety guards used on cutting-off and surface
,grinding machines, which employ the wheel periphery, shall not exceed 150
degrees. This exposure shall begin at a point not less than 15 degrees below the
horizontal plane of the wheel spindle.
What is the "Ring Test" as described in 29 CFR 1910.215(d)(1) and 215(d)(1)(i)? -
ANSWER Wheels should be tapped gently with a light nonmetallic implement,
and if the sound cracked (dead) they shall not be used.
What are the requirements for guarding horizontal shafting seven feet or less from
the floor according to 29 CFR 1910.219(c)(2)(i)? - ANSWER Shall be protected
by a stationary casing enclosing shafting completely or by a trough enclosing sides
and top or sides and bottom of shafting as location requires.
What are the requirements for shaft couplings according to 29 CFR
1910.219(i)(2)? - ANSWER Shall be so constructed as to present no hazards
from bolts, nuts, setscrews, or revolving surfaces. Bolts, nuts, and setscrews will be
permitted when covered with safety sleeves or where they are used parallel and
countersunk with shafting.
According to 29 CFR 1910.219(p)(7), what are the requirements for the person or
oiler when lubricating machinery? - ANSWER Must wear tight-fitting clothing
and machinery shall be oiled when not in motion (if possible).
Question 1: Is Adrian Smith, one of 3 employees of ABC Landscaping, covered by
OSHA? - ANSWER A. Yes
Question 2: Is Taylor Dell, an accountant in business for herself, covered by
OSHA? - ANSWER B. No
, Question 3: Is Rob Jones, one of 10 carpenters working for Woody, Inc., covered
by OSHA? - ANSWER A. Yes
Question 4: Why was OSHA necessary?
A. Workplace injuries, illnesses and death were increasing
B. No uniform or Comprehensive law existed to protect against workplace hazards
C. None of the Above
D. Both A and B - ANSWER D. Both A and B
Question 5: What is OSHA's mission?
A. To save lives
B. To prevent injuries
C. Protect the health of America's workers
D. All the answers are correct - ANSWER D. All the answers are correct
Question 6: Why is this training important?
A. You'll know your rights if there are hazards in your workplace.
B. You'll know where to get help.
C. You'll know if your employer is complying with OSHA standards.
D. All of the answers are correct - ANSWER D. All of the answers are correct
Question 1: What are some of the things you might find on an SDS?
A. Chemical Name
B. You'll know where to get help
