AMPP STANDARDS QUESTIONS AND ANSWERS
ASTM D6312-97 - Answers - Standard test method for non-destructive measurement of
dry film thickness of applied organic coatings over concrete using an ultrasonic gauge.
ASTM - D4263 - Answers - Standard test method for indicating moisture in concrete by
plastic sheet method, a segment of 1 mm to 4 mm thick clear polyethylene sheet
approximately 18" x 18" is taped over the concrete to be tested so that the concrete is
tightly sealed from the atmosphere and sunlight, the test patch is allowed to stay on and
minimum of 16 hours
ASTM - F - 1869 - Answers - Calcium chloride test
ASTM - F2170-02 - Answers - Standard test method for determining relative humidity in
concrete floor slabs using in In Situ probes
ASTM D 4787 - Answers - Standard Practice for Continuity Verification of Liquid or
Sheet Linings Applied to Concrete Substrates, low voltage holiday tester
ASTM D 4262 - Answers - Standard method for testing ph of chemically cleaned or
etched concrete surface
ASTM D 4258 - Answers - standard practice for surface cleaning concrete for coating
ASTM D 4259 - Answers - standard practice for abrading concrete
ASTM D 4260 - Answers - Standard Practice for Acid Etching Concrete
ASTM D 4261 - Answers - standard practice for surface cleaning concrete unit masonry
for coating
ASTM D 4752 - Answers - test method for measuring MEK resistance of Ethyl Silicate
Zinc-Rich primers by solvent rub
ASTM D 5402 - Answers - test method for measuring solvent resistance of organic
coatings. Is performed the same way as an organic coatings using an agreed-upon
solvent.
ASTM D 4138 - Answers - Measurement of dry film thickness of protective coding
systems by destructive means method A Tooke gauges ISO 2808-53 and ISO 2409
ASTM D 4138 method C - Answers - Is the use of a specific angle tip drill bit to cut a
Choco cavity in the coating. This is a saberg drill which creates a counter sink hole in
the coating and substrate.
ASTM D6312-97 - Answers - Standard test method for non-destructive measurement of
dry film thickness of applied organic coatings over concrete using an ultrasonic gauge.
ASTM - D4263 - Answers - Standard test method for indicating moisture in concrete by
plastic sheet method, a segment of 1 mm to 4 mm thick clear polyethylene sheet
approximately 18" x 18" is taped over the concrete to be tested so that the concrete is
tightly sealed from the atmosphere and sunlight, the test patch is allowed to stay on and
minimum of 16 hours
ASTM - F - 1869 - Answers - Calcium chloride test
ASTM - F2170-02 - Answers - Standard test method for determining relative humidity in
concrete floor slabs using in In Situ probes
ASTM D 4787 - Answers - Standard Practice for Continuity Verification of Liquid or
Sheet Linings Applied to Concrete Substrates, low voltage holiday tester
ASTM D 4262 - Answers - Standard method for testing ph of chemically cleaned or
etched concrete surface
ASTM D 4258 - Answers - standard practice for surface cleaning concrete for coating
ASTM D 4259 - Answers - standard practice for abrading concrete
ASTM D 4260 - Answers - Standard Practice for Acid Etching Concrete
ASTM D 4261 - Answers - standard practice for surface cleaning concrete unit masonry
for coating
ASTM D 4752 - Answers - test method for measuring MEK resistance of Ethyl Silicate
Zinc-Rich primers by solvent rub
ASTM D 5402 - Answers - test method for measuring solvent resistance of organic
coatings. Is performed the same way as an organic coatings using an agreed-upon
solvent.
ASTM D 4138 - Answers - Measurement of dry film thickness of protective coding
systems by destructive means method A Tooke gauges ISO 2808-53 and ISO 2409
ASTM D 4138 method C - Answers - Is the use of a specific angle tip drill bit to cut a
Choco cavity in the coating. This is a saberg drill which creates a counter sink hole in
the coating and substrate.
