MP100 Review Cycle 3 Exam ACTUAL
QUESTIONS AND CORRECT ANSWERS
Insert - CORRECT ANSWER Should a compressor be patched across the aux send or insert?
D. a band-pass filter - CORRECT ANSWER What is a high-pass and low-pass filter used in
conjunction?
A. a plugo filter
B. a band
C. post-war filter
D. a band-pass filter
B. Stopband - CORRECT ANSWER On a high/low pass filter, frequencies attenuated more
than 3dB are in the ___________.
A. turnover
B. stopband
C. passband
C. Passband - CORRECT ANSWER On a high/low pass filter, frequencies attenuated less than
3dB are in the ___________.
A. filter
B. stopband
C. passband
C. A Y-split is a pre Fader Fader split into the Monitor Fader, after being processed by an insert, filter,
or EQ. It is achieved by pressing both "IN" buttons in your processor section on any I/O. - CORRECT
ANSWER What is a Y-split on the Neotek and how is it achieved?
, A. A Y-split is an adapter that allows 2 devices to receive the output from from a single source. The
split is achieved by plugging the Y-split into the jack and plugging two separate male ends into the
female ends of the adapter.
B. A Y-split is the use of the output of any fader to send to mutiple destinations. It is achieved by
directing the output of a fader to the multitrack bus and either selecting more than one output, and/or
by simply not utilizing the track pan (leaving it in the "noon" postition).
C. A Y-split is a pre Fader Fader split into the Monitor Fader, after being processed by an insert, filter,
or EQ. It is achieved by pressing both "IN" buttons in your processor section on any I/O.
D. A Y-split is a fancy name for multiplying a single signal and directing it to multiple pieces of gear
or multiple inputs on one piece of gear. It is achieved on the patchbay by sending the output of an
auxiliary bus into a mult.
E. A Y-split is a pre or post fader auxiliary send and is achieved by selecting the desired postion of the
FADER button in the Aux Sends section of any I/O.
375 - CORRECT ANSWER What is the highest frequency the High Pass Filter can be dialed to
on the Neotek?
False - CORRECT ANSWER True or False: When mixing, your auxiliary send(s) for purposes
of parallel compression should be post-fader.
C. All Repro - CORRECT ANSWER What mode should the MTR-90 be in for a mixing
session?
a. All Sel-Rep
b. Vari-speed
c. All Repro
d. All Input
e. Zero Set
26 - CORRECT ANSWER How many multitrack buses does the Neotek Elite console offer?
QUESTIONS AND CORRECT ANSWERS
Insert - CORRECT ANSWER Should a compressor be patched across the aux send or insert?
D. a band-pass filter - CORRECT ANSWER What is a high-pass and low-pass filter used in
conjunction?
A. a plugo filter
B. a band
C. post-war filter
D. a band-pass filter
B. Stopband - CORRECT ANSWER On a high/low pass filter, frequencies attenuated more
than 3dB are in the ___________.
A. turnover
B. stopband
C. passband
C. Passband - CORRECT ANSWER On a high/low pass filter, frequencies attenuated less than
3dB are in the ___________.
A. filter
B. stopband
C. passband
C. A Y-split is a pre Fader Fader split into the Monitor Fader, after being processed by an insert, filter,
or EQ. It is achieved by pressing both "IN" buttons in your processor section on any I/O. - CORRECT
ANSWER What is a Y-split on the Neotek and how is it achieved?
, A. A Y-split is an adapter that allows 2 devices to receive the output from from a single source. The
split is achieved by plugging the Y-split into the jack and plugging two separate male ends into the
female ends of the adapter.
B. A Y-split is the use of the output of any fader to send to mutiple destinations. It is achieved by
directing the output of a fader to the multitrack bus and either selecting more than one output, and/or
by simply not utilizing the track pan (leaving it in the "noon" postition).
C. A Y-split is a pre Fader Fader split into the Monitor Fader, after being processed by an insert, filter,
or EQ. It is achieved by pressing both "IN" buttons in your processor section on any I/O.
D. A Y-split is a fancy name for multiplying a single signal and directing it to multiple pieces of gear
or multiple inputs on one piece of gear. It is achieved on the patchbay by sending the output of an
auxiliary bus into a mult.
E. A Y-split is a pre or post fader auxiliary send and is achieved by selecting the desired postion of the
FADER button in the Aux Sends section of any I/O.
375 - CORRECT ANSWER What is the highest frequency the High Pass Filter can be dialed to
on the Neotek?
False - CORRECT ANSWER True or False: When mixing, your auxiliary send(s) for purposes
of parallel compression should be post-fader.
C. All Repro - CORRECT ANSWER What mode should the MTR-90 be in for a mixing
session?
a. All Sel-Rep
b. Vari-speed
c. All Repro
d. All Input
e. Zero Set
26 - CORRECT ANSWER How many multitrack buses does the Neotek Elite console offer?
