NC Building Contractor License
- ANS-What board is nailed to the end of a rafter tail?
.25 of an inch - ANS-The minimum thickness for fiber cement lap siding as weather masking is
_____
.0149 of an inch - ANS-Metal veneer siding shall have a minimal thickness of______
#12 - ANS-The minimal length screws used to connect metal decking are__________.
$6,740 - ANS-The agenda of values for a mission shows Task A is worth $18,000, Task B is well
worth $6,500 and Task Cis worth $45,000. Task A is 16% complete. Task B is four% whole and
Task Cis eight% complete. What is the fee of the development fee due?
$50,441 - ANS-If your account stability is $47,382 on May 11th and all through May you pay
$11,318 worth of involces, and you deposit $14,377, what is your balance on June 2nd?
$one hundred,000 - ANS-The Miller Act calls for that all federal tasks exceeding ____________
need to be bonded.
$152,000 - ANS-If a contractor made $38,000 on a challenge and this represented 25% profit,
what became the entire quantity of the task?
0.024 inches - ANS-What is the minimal thickness of aluminum used as valley lining cloth?
Zero.028 - ANS-Weld washers are recommended for metallic thickness much less
than_______.
1 - ANS-Plain bevel siding must overlap at the least ________ inches.
1 half inch - ANS-Clear space between a handrail and a wall/ surface shall be no longer much
less than _____
1 1/2 inch - ANS-What is the minimal concrete cover (in inches) for a W31 piece of rebar, while
the usage of Hign- early power concrete on a patio slab?
1 half of inch. 3 inches - ANS-The ends of arch joist shall have no longer less than ________
inches of touching on wooden/metallic or now not much less than ______ on masonry
,1 half of to 1 three/four percentage - ANS-What is the allowable slope for a aspect-to facet
sloped football discipline.
1 three/four inches - ANS-Max 2 inches circular handrails shall have a diameter no extra than
_____ and no more than _____
1 Acre or Larger - ANS-An erosion and sedimentation manage plan need to be authorised
before land distrubance begins on any web page ______
1 inch - ANS-The edges of lugs, brackets, rivets and bolt heads attached to structural members
will be accredited to extend to inside ___ of the floor of the fire protection/fireproofing
1 inch - ANS-The maximum distance to cut back the sheathing from a publish-tension strand for
the anchor is______.
1 inch - ANS-Ventilation necessities: an air space/gap of ___ is required between the insulation
and the roof sheathing
1 layer of felt - ANS-Underlayment application: for roof slopes four devices in 12 gadgets
horizontal (33% slope) ___________ is required
1 unit vertical and 12 units horizontal - ANS-Ramps used as a part of a way of egress shall have
a walking slop no steeper than __ vertical in ___ horizontal
1-half of - ANS-The sidelap or offset for wooden shingles and shakes have to be _________
inches.
1-half of - ANS-The space among a wall and a grab bar shall be _____ inches.
1-1/2 horizontal to at least one vertical - ANS-The maximum slope allowed for excavation less
than 20 ft in total intensity in a Type C soilis ___________.
1-1/2 hours, 300 revolutions - ANS-When it involves geared up blended concrete, what time
frame do you've got from batching on the plant to finish discharge at the jobsite?
1-1/2 x 3-half of - ANS-The actual length of a 2 x 4 is___________.
1:12 - ANS-The maximum slope of a ramp is ________?
1:12 - ANS-Which of the subsequent is the maximum slope allowed for a ramp?
1:20(5percentslope) - ANS-10 toes Site grading: the grade shall be sloped away from a
constructing no much less than ______ for a minimal distance of ______ feet.
, 1.5. 4 - ANS-Normally the travel pace of a dozer is ______ to ______ mph.
1.054 - ANS-The roof slope element for a 4 in 12 roof slope is__________.
1) Chain and hook via the center of the bundles
2) Forklift blades
3) Nylon straps used as a choker
4) None of the above. ******* - ANS-The great technique for unloading put up-tensioning cable
would be..
Half - ANS-A concrete wearing floor like terrazzo is generally ________ inch thick.
Half of inch thick - ANS-Combustible insulating boards no more than___ & protected with finish
flooring are accredited whilst connected at once to non combustible ground or timber subfloor
connected to sleepers
1/2 inch type X gypsum board (private storage separated from dwelling unit and its attic) -
ANS-What should be applied to systems helping the separation from liveable rooms above the
garage?
Half inch. 6 feet 15 inches - ANS-Roof diaphragms will be anchored to masonry partitions with
______. Diameter bolts ________feet on middle or their equivalent. Bolts shall expand and be
embedded as a minimum _____ inches into the masonry.
1/2" - ANS-When wooden beams are positioned interior a masonry or concrete pocket how a
good deal clearance is required on pinnacle, aspects and quit of the beam?
1/three - ANS-The overall area of mezzanines have to now not exceed _____ of the room in
which it's miles placed
1/four - ANS-Ladders located towards a wall need to be sloped in order that the horizontal
distance from the foot of the ladder to the wall _______ is of the operating duration of the
ladder.
1/4 - ANS-Notches at the ends of joists shall now not exceed ______ the joist depth
1/4 inch. 3/four inch - ANS-A mortar mattress on pinnacle of a footing should be among
__________ and ___________.
1/4 inches at 2 inches - ANS-The proper give up ancore weld for a deep lengthy span joist is
________.
1/four the depth - ANS-Notching on the ends of rafters ceiling joists shall no longer exceed
________
- ANS-What board is nailed to the end of a rafter tail?
.25 of an inch - ANS-The minimum thickness for fiber cement lap siding as weather masking is
_____
.0149 of an inch - ANS-Metal veneer siding shall have a minimal thickness of______
#12 - ANS-The minimal length screws used to connect metal decking are__________.
$6,740 - ANS-The agenda of values for a mission shows Task A is worth $18,000, Task B is well
worth $6,500 and Task Cis worth $45,000. Task A is 16% complete. Task B is four% whole and
Task Cis eight% complete. What is the fee of the development fee due?
$50,441 - ANS-If your account stability is $47,382 on May 11th and all through May you pay
$11,318 worth of involces, and you deposit $14,377, what is your balance on June 2nd?
$one hundred,000 - ANS-The Miller Act calls for that all federal tasks exceeding ____________
need to be bonded.
$152,000 - ANS-If a contractor made $38,000 on a challenge and this represented 25% profit,
what became the entire quantity of the task?
0.024 inches - ANS-What is the minimal thickness of aluminum used as valley lining cloth?
Zero.028 - ANS-Weld washers are recommended for metallic thickness much less
than_______.
1 - ANS-Plain bevel siding must overlap at the least ________ inches.
1 half inch - ANS-Clear space between a handrail and a wall/ surface shall be no longer much
less than _____
1 1/2 inch - ANS-What is the minimal concrete cover (in inches) for a W31 piece of rebar, while
the usage of Hign- early power concrete on a patio slab?
1 half of inch. 3 inches - ANS-The ends of arch joist shall have no longer less than ________
inches of touching on wooden/metallic or now not much less than ______ on masonry
,1 half of to 1 three/four percentage - ANS-What is the allowable slope for a aspect-to facet
sloped football discipline.
1 three/four inches - ANS-Max 2 inches circular handrails shall have a diameter no extra than
_____ and no more than _____
1 Acre or Larger - ANS-An erosion and sedimentation manage plan need to be authorised
before land distrubance begins on any web page ______
1 inch - ANS-The edges of lugs, brackets, rivets and bolt heads attached to structural members
will be accredited to extend to inside ___ of the floor of the fire protection/fireproofing
1 inch - ANS-The maximum distance to cut back the sheathing from a publish-tension strand for
the anchor is______.
1 inch - ANS-Ventilation necessities: an air space/gap of ___ is required between the insulation
and the roof sheathing
1 layer of felt - ANS-Underlayment application: for roof slopes four devices in 12 gadgets
horizontal (33% slope) ___________ is required
1 unit vertical and 12 units horizontal - ANS-Ramps used as a part of a way of egress shall have
a walking slop no steeper than __ vertical in ___ horizontal
1-half of - ANS-The sidelap or offset for wooden shingles and shakes have to be _________
inches.
1-half of - ANS-The space among a wall and a grab bar shall be _____ inches.
1-1/2 horizontal to at least one vertical - ANS-The maximum slope allowed for excavation less
than 20 ft in total intensity in a Type C soilis ___________.
1-1/2 hours, 300 revolutions - ANS-When it involves geared up blended concrete, what time
frame do you've got from batching on the plant to finish discharge at the jobsite?
1-1/2 x 3-half of - ANS-The actual length of a 2 x 4 is___________.
1:12 - ANS-The maximum slope of a ramp is ________?
1:12 - ANS-Which of the subsequent is the maximum slope allowed for a ramp?
1:20(5percentslope) - ANS-10 toes Site grading: the grade shall be sloped away from a
constructing no much less than ______ for a minimal distance of ______ feet.
, 1.5. 4 - ANS-Normally the travel pace of a dozer is ______ to ______ mph.
1.054 - ANS-The roof slope element for a 4 in 12 roof slope is__________.
1) Chain and hook via the center of the bundles
2) Forklift blades
3) Nylon straps used as a choker
4) None of the above. ******* - ANS-The great technique for unloading put up-tensioning cable
would be..
Half - ANS-A concrete wearing floor like terrazzo is generally ________ inch thick.
Half of inch thick - ANS-Combustible insulating boards no more than___ & protected with finish
flooring are accredited whilst connected at once to non combustible ground or timber subfloor
connected to sleepers
1/2 inch type X gypsum board (private storage separated from dwelling unit and its attic) -
ANS-What should be applied to systems helping the separation from liveable rooms above the
garage?
Half inch. 6 feet 15 inches - ANS-Roof diaphragms will be anchored to masonry partitions with
______. Diameter bolts ________feet on middle or their equivalent. Bolts shall expand and be
embedded as a minimum _____ inches into the masonry.
1/2" - ANS-When wooden beams are positioned interior a masonry or concrete pocket how a
good deal clearance is required on pinnacle, aspects and quit of the beam?
1/three - ANS-The overall area of mezzanines have to now not exceed _____ of the room in
which it's miles placed
1/four - ANS-Ladders located towards a wall need to be sloped in order that the horizontal
distance from the foot of the ladder to the wall _______ is of the operating duration of the
ladder.
1/4 - ANS-Notches at the ends of joists shall now not exceed ______ the joist depth
1/4 inch. 3/four inch - ANS-A mortar mattress on pinnacle of a footing should be among
__________ and ___________.
1/4 inches at 2 inches - ANS-The proper give up ancore weld for a deep lengthy span joist is
________.
1/four the depth - ANS-Notching on the ends of rafters ceiling joists shall no longer exceed
________
