1|Page
CCSE - PRACTICE EXAM | CCSE R80 PRACTICE |
2026/2027 NEW UPDATE | COMPLETE ACTUAL
AND AUTHENTIC EXAM | BRAND NEW!
SSL Network Extender (SNX) is a thin SSL VPN on-demand client that is
installed on the remote user's machine via the web browser. What are
the two modes of SNX?
A. Application and Client Service
B. Network and Application
C. Network and Layers
D. Virtual Adapter and Mobile App ......ANSWER......B.
Which two of these Check Point Protocols are used by SmartEvent
Processes?
A. ELA and CPD
B. FWD and LEA
C. FWD and CPLOG
D. ELA and CPLOG ......ANSWER......D.
Which command will allow you to see the interface status?
pg. 1
,2|Page
A. cphaprob interface
B. cphaprob -I interface
C. cphaprob -a if
D. cphaprob stat ......ANSWER......C.
Which command can you use to enable or disable multi-queue per
interface?
A. cpmq set
B. Cpmqueue set
C. Cpmq config
D. Set cpmq enable ......ANSWER......A.
To help SmartEvent determine whether events originated internally or
externally you must define using the Initial Settings under General
Settings in the Policy Tab. How many options are available to calculate
the traffic direction?
A. 5 Network; Host; Objects; Services; API
B. 3 Incoming; Outgoing; Network
C. 2 Internal; External
D. 4 Incoming; Outgoing; Internal; Other ......ANSWER......D.
pg. 2
,3|Page
CoreXL is supported when one of the following features is enabled:
A. Route-based VPN
B. IPS
C. IPv6
D. Overlapping NAT ......ANSWER......D.
You noticed that CPU cores on the Security Gateway are usually 100%
utilized and many packets were dropped. You don't have a budget to
perform a hardware upgrade at this time. To optimize drops you decide
to use Priority Queues and fully enable Dynamic Dispatcher. How can
you enable them?
A. fw ctl multik dynamic_dispatching on
B. fw ctl multik dynamic_dispatching set_mode 9
C. fw ctl multik set_mode 9
D. fw ctl multik pq enable ......ANSWER......A.
Which command is used to set the CCP protocol to Multicast?
A. cphaprob set_ccp multicast
B. cphaconf set_ccp multicast
pg. 3
, 4|Page
C. cphaconf set_ccp no_broadcast
D. cphaprob set_ccp no_broadcast ......ANSWER......B.
Which packet info is ignored with Session Rate Acceleration?
A. source port ranges
B. source ip
C. source port
D. same info from Packet Acceleration is used ......ANSWER......C.
Which is the least ideal Synchronization Status for Security
Management Server High Availability deployment?
A. Synchronized
B. Never been synchronized
C. Lagging
D. Collision ......ANSWER......D.
During inspection of your Threat Prevention logs you find four different
computers having one event each with a Critical Severity. Which of
those hosts should you try to remediate first?
A. Host having a Critical event found by Threat Emulation
pg. 4
CCSE - PRACTICE EXAM | CCSE R80 PRACTICE |
2026/2027 NEW UPDATE | COMPLETE ACTUAL
AND AUTHENTIC EXAM | BRAND NEW!
SSL Network Extender (SNX) is a thin SSL VPN on-demand client that is
installed on the remote user's machine via the web browser. What are
the two modes of SNX?
A. Application and Client Service
B. Network and Application
C. Network and Layers
D. Virtual Adapter and Mobile App ......ANSWER......B.
Which two of these Check Point Protocols are used by SmartEvent
Processes?
A. ELA and CPD
B. FWD and LEA
C. FWD and CPLOG
D. ELA and CPLOG ......ANSWER......D.
Which command will allow you to see the interface status?
pg. 1
,2|Page
A. cphaprob interface
B. cphaprob -I interface
C. cphaprob -a if
D. cphaprob stat ......ANSWER......C.
Which command can you use to enable or disable multi-queue per
interface?
A. cpmq set
B. Cpmqueue set
C. Cpmq config
D. Set cpmq enable ......ANSWER......A.
To help SmartEvent determine whether events originated internally or
externally you must define using the Initial Settings under General
Settings in the Policy Tab. How many options are available to calculate
the traffic direction?
A. 5 Network; Host; Objects; Services; API
B. 3 Incoming; Outgoing; Network
C. 2 Internal; External
D. 4 Incoming; Outgoing; Internal; Other ......ANSWER......D.
pg. 2
,3|Page
CoreXL is supported when one of the following features is enabled:
A. Route-based VPN
B. IPS
C. IPv6
D. Overlapping NAT ......ANSWER......D.
You noticed that CPU cores on the Security Gateway are usually 100%
utilized and many packets were dropped. You don't have a budget to
perform a hardware upgrade at this time. To optimize drops you decide
to use Priority Queues and fully enable Dynamic Dispatcher. How can
you enable them?
A. fw ctl multik dynamic_dispatching on
B. fw ctl multik dynamic_dispatching set_mode 9
C. fw ctl multik set_mode 9
D. fw ctl multik pq enable ......ANSWER......A.
Which command is used to set the CCP protocol to Multicast?
A. cphaprob set_ccp multicast
B. cphaconf set_ccp multicast
pg. 3
, 4|Page
C. cphaconf set_ccp no_broadcast
D. cphaprob set_ccp no_broadcast ......ANSWER......B.
Which packet info is ignored with Session Rate Acceleration?
A. source port ranges
B. source ip
C. source port
D. same info from Packet Acceleration is used ......ANSWER......C.
Which is the least ideal Synchronization Status for Security
Management Server High Availability deployment?
A. Synchronized
B. Never been synchronized
C. Lagging
D. Collision ......ANSWER......D.
During inspection of your Threat Prevention logs you find four different
computers having one event each with a Critical Severity. Which of
those hosts should you try to remediate first?
A. Host having a Critical event found by Threat Emulation
pg. 4
