Adhesive Anchor Training Exam Questions
With Correct Answers
minimum anchor spacing and edge distance, as well as minimum member
| | | | | | | | | | |
thickness, must comply with the values given - CORRECT ANSWER✔✔-In the
| | | | | | | | | | |
products ICC-ES Report | |
The registered design professional in responsible charge and the engineers of
| | | | | | | | | | |
record involved in the design of the project are permitted to act as the - CORRECT
| | | | | | | | | | | | | | |
ANSWER✔✔-Approved Agency
| |
If reinforcing bars are encountered during drilling the correct action would be -
| | | | | | | | | | | | |
CORRECT ANSWER✔✔-Consulting with the EOR
| | | |
for adhesive anchors, the characteristics bond stresses and suitability for
| | | | | | | | | |
structural applications are established by testing in accordance with - CORRECT
| | | | | | | | | | |
ANSWER✔✔-ACI 355.4 |
Special inspections and tests shall be required for proposal work that is, in the
| | | | | | | | | | | | | |
opinion of the building official, unusual in its nature, as such, but not limited to -
| | | | | | | | | | | | | | | |
CORRECT ANSWER✔✔-All of the above
| | | |
ACI 355.4, qualification of post installed adhesive anchors in concrete, is
| | | | | | | | | | |
applicable to anchors with a specified minimum embedment depth of - CORRECT
| | | | | | | | | | | |
ANSWER✔✔-1 - 5/8 inches | | |
, Proof loads are usually determined as a - CORRECT ANSWER✔✔-Percentage of
| | | | | | | | | | |
the anchor ultimate tensile strength
| | | |
True or False: The contractor is permitted to employ the approved agencies for
| | | | | | | | | | | | |
special inspection where the contractor is also the owner of the project? -
| | | | | | | | | | | | |
CORRECT ANSWER✔✔-True |
The effective embedment depth, measure from the concrete surface to the
| | | | | | | | | | |
deepest point at which bond to the concrete is established is identified as -
| | | | | | | | | | | | | |
CORRECT ANSWER✔✔-h subscript(ef)
| |
True or false: Powers PE1000+ epoxy adhesive are recognized for use to resist
| | | | | | | | | | | | |
short-term and long-term loads, including wind and earthquake loads, subject to
| | | | | | | | | | |
conditions of the ICC-ES Evaluation report? - CORRECT ANSWER✔✔-True
| | | | | | | |
Short sections of anchor rods the have been burned or sawed are indictive of: -
| | | | | | | | | | | | | | |
CORRECT ANSWER✔✔-Incorrect embedment
| |
The elapsed time after mixing adhesive material components to onset of
| | | | | | | | | | |
significant chemical reaction as characterized by an increase in viscosity is -
| | | | | | | | | | | |
CORRECT ANSWER✔✔-Gel Time | |
Periodic and final inspection reports are required to be summited to the -
| | | | | | | | | | | | |
CORRECT ANSWER✔✔-Building official and engineer or architect of record
| | | | | | | |
Powers PE1000+ epoxy adhesive anchors must be installed in accordance with? -
| | | | | | | | | | | |
CORRECT ANSWER✔✔-The manufacturers published installation instructions
| | | | |
With Correct Answers
minimum anchor spacing and edge distance, as well as minimum member
| | | | | | | | | | |
thickness, must comply with the values given - CORRECT ANSWER✔✔-In the
| | | | | | | | | | |
products ICC-ES Report | |
The registered design professional in responsible charge and the engineers of
| | | | | | | | | | |
record involved in the design of the project are permitted to act as the - CORRECT
| | | | | | | | | | | | | | |
ANSWER✔✔-Approved Agency
| |
If reinforcing bars are encountered during drilling the correct action would be -
| | | | | | | | | | | | |
CORRECT ANSWER✔✔-Consulting with the EOR
| | | |
for adhesive anchors, the characteristics bond stresses and suitability for
| | | | | | | | | |
structural applications are established by testing in accordance with - CORRECT
| | | | | | | | | | |
ANSWER✔✔-ACI 355.4 |
Special inspections and tests shall be required for proposal work that is, in the
| | | | | | | | | | | | | |
opinion of the building official, unusual in its nature, as such, but not limited to -
| | | | | | | | | | | | | | | |
CORRECT ANSWER✔✔-All of the above
| | | |
ACI 355.4, qualification of post installed adhesive anchors in concrete, is
| | | | | | | | | | |
applicable to anchors with a specified minimum embedment depth of - CORRECT
| | | | | | | | | | | |
ANSWER✔✔-1 - 5/8 inches | | |
, Proof loads are usually determined as a - CORRECT ANSWER✔✔-Percentage of
| | | | | | | | | | |
the anchor ultimate tensile strength
| | | |
True or False: The contractor is permitted to employ the approved agencies for
| | | | | | | | | | | | |
special inspection where the contractor is also the owner of the project? -
| | | | | | | | | | | | |
CORRECT ANSWER✔✔-True |
The effective embedment depth, measure from the concrete surface to the
| | | | | | | | | | |
deepest point at which bond to the concrete is established is identified as -
| | | | | | | | | | | | | |
CORRECT ANSWER✔✔-h subscript(ef)
| |
True or false: Powers PE1000+ epoxy adhesive are recognized for use to resist
| | | | | | | | | | | | |
short-term and long-term loads, including wind and earthquake loads, subject to
| | | | | | | | | | |
conditions of the ICC-ES Evaluation report? - CORRECT ANSWER✔✔-True
| | | | | | | |
Short sections of anchor rods the have been burned or sawed are indictive of: -
| | | | | | | | | | | | | | |
CORRECT ANSWER✔✔-Incorrect embedment
| |
The elapsed time after mixing adhesive material components to onset of
| | | | | | | | | | |
significant chemical reaction as characterized by an increase in viscosity is -
| | | | | | | | | | | |
CORRECT ANSWER✔✔-Gel Time | |
Periodic and final inspection reports are required to be summited to the -
| | | | | | | | | | | | |
CORRECT ANSWER✔✔-Building official and engineer or architect of record
| | | | | | | |
Powers PE1000+ epoxy adhesive anchors must be installed in accordance with? -
| | | | | | | | | | | |
CORRECT ANSWER✔✔-The manufacturers published installation instructions
| | | | |
