5/20/26, 8:53 AM Michigan State Brakes Certification Exam comprehensive questions fully solved & updated (Latest Update 2026) UPDATE!! Flashc…
Michigan State Brakes Certification Exam
comprehensive questions fully solved & updated
(Latest Update 2026) UPDATE!!
Save Groups
Terms in this set (63)
Most 1995 & newer vehicles use Sealed non-serviceable
which of the following types of
wheels bearings on non-drive
wheel?
to test a vacuum power brake drop slightly and remain firm
booster in the vehicle, you should
pump the brake pedal at least 4
times, hold the brake pedal
depressed, and start the engine. the
brake pedal should:
You are installing a set of brake shoe Smaller and goes towards the front of the car.
linings that are not the same length.
Traditionally, the primary shoe lining
is:
A cracked or torn vacuum diaphragm a hard pedal feel requiring very high pedal effort
in a brake power booster would to stop
most likely cause:
https://quizlet.com/1182352620/michigan-state-brakes-certification-exam-comprehensive-questions-fully-solved-updated-latest-update-2026-update-fla… 1/9
, 5/20/26, 8:53 AM Michigan State Brakes Certification Exam comprehensive questions fully solved & updated (Latest Update 2026) UPDATE!! Flashc…
A mechanic finds gear lube inside A plugged axle
both rear brake drums on a rear
wheel drive vehicle. What is the most
likely cause of this problem?
Which of the following incorrect master cylinder push rod adjusted too long
service procedures will cause brake
lock-up?
Which of the following describes the Pump the brake pedal at least 25 times (or more,
proper way to depressurized an ABS depending on the manufacturer's
system? recommendation) with the ignition off.
The rear brakes are dragging after technician use the parking brake to adjust shoes
having new linings installed and the and the cable is stuck
drums machined. the most likely
cause is the:
When turning brake drums: use a dampening strap to reduce chatter
Which of the following is NOT a run-out
necessary drum brake
measurement?
On a 3-channel system, which both rear wheels
wheels are on the same circuit?
One way to test an ABS wheel speed AC volts
signal is to use _____ on your digital
multimeter.
The key input for the ABS control wheel speed sensors
module comes from the:
https://quizlet.com/1182352620/michigan-state-brakes-certification-exam-comprehensive-questions-fully-solved-updated-latest-update-2026-update-fla… 2/9
Michigan State Brakes Certification Exam
comprehensive questions fully solved & updated
(Latest Update 2026) UPDATE!!
Save Groups
Terms in this set (63)
Most 1995 & newer vehicles use Sealed non-serviceable
which of the following types of
wheels bearings on non-drive
wheel?
to test a vacuum power brake drop slightly and remain firm
booster in the vehicle, you should
pump the brake pedal at least 4
times, hold the brake pedal
depressed, and start the engine. the
brake pedal should:
You are installing a set of brake shoe Smaller and goes towards the front of the car.
linings that are not the same length.
Traditionally, the primary shoe lining
is:
A cracked or torn vacuum diaphragm a hard pedal feel requiring very high pedal effort
in a brake power booster would to stop
most likely cause:
https://quizlet.com/1182352620/michigan-state-brakes-certification-exam-comprehensive-questions-fully-solved-updated-latest-update-2026-update-fla… 1/9
, 5/20/26, 8:53 AM Michigan State Brakes Certification Exam comprehensive questions fully solved & updated (Latest Update 2026) UPDATE!! Flashc…
A mechanic finds gear lube inside A plugged axle
both rear brake drums on a rear
wheel drive vehicle. What is the most
likely cause of this problem?
Which of the following incorrect master cylinder push rod adjusted too long
service procedures will cause brake
lock-up?
Which of the following describes the Pump the brake pedal at least 25 times (or more,
proper way to depressurized an ABS depending on the manufacturer's
system? recommendation) with the ignition off.
The rear brakes are dragging after technician use the parking brake to adjust shoes
having new linings installed and the and the cable is stuck
drums machined. the most likely
cause is the:
When turning brake drums: use a dampening strap to reduce chatter
Which of the following is NOT a run-out
necessary drum brake
measurement?
On a 3-channel system, which both rear wheels
wheels are on the same circuit?
One way to test an ABS wheel speed AC volts
signal is to use _____ on your digital
multimeter.
The key input for the ABS control wheel speed sensors
module comes from the:
https://quizlet.com/1182352620/michigan-state-brakes-certification-exam-comprehensive-questions-fully-solved-updated-latest-update-2026-update-fla… 2/9
