, TESTBANK FOR Electric and Hybrid Electric
Vehicles, 1st edition James Halderman
Notes
1- The file is chapter after chapter.
2- We have shown you few pages sample.
3- The file contains all Appendix and Excel sheet
if it exists.
4- We have all what you need, we make update
at every time. There are many new editions
waiting you.
5- If you think you purchased the wrong file You
can contact us at every time, we can replace it
with true one.
Our email:
,Electric and Hybrid Electric Vehicles, 1e (Halderman)
Chapter 1 Hybrid and Electric Vehicle Safety
1) Rubber gloves should be worn whenever working on or near the high-voltage circuits or
components of a hybrid electric vehicle. Technician says A that the rubber gloves should be rated
at 1000 volts or higher. Technician B says that leather gloves should be worn over the high-
voltage rubber gloves. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: C
Page Ref: 4
Objective: 1-4 List the types of personal protective equipment.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
2) A CAT III certified DMM should be used whenever measuring high-voltage circuits or
components. The
CAT III rating relates to ________.
A) high voltage
B) high energy
C) high electrical resistance
D) both high energy and high voltage
Answer: D
Page Ref: 7
Objective: 1-2 Describe the differences between a CAT I, CAT II, CAT III, and CAT IV
multimeter.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
3) All of the following will shut off the high voltage to components and circuits EXCEPT
________.
A) opening the driver's door
B) turning the ignition off
C) disconnecting the 12-volt auxiliary battery
D) removing the main fuse, relay, or HV plug
Answer: A
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
1
Copyright © 2023 Pearson Education, Inc.
,4) What can occur if a hybrid electric vehicle is pushed in the shop?
A) The HV battery pack can be damaged.
B) The tires will be locked unless the ignition is on.
C) Damage to the electronic controller can occur.
D) High voltage will be generated by the motor/generator as the wheels turn.
Answer: D
Page Ref: 10
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
5) When hoisting a hybrid or electric vehicle, what precautions must the technician follow to
ensure personal safety and avoid damage to the vehicle?
A) Make sure the lift points do not contact HV cables.
B) Do not lift the vehicle by the battery case.
C) Ensure the lift points are clear of battery cooling and refrigeration lines.
D) All of the answers are correct.
Answer: D
Page Ref: 9
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
6) When does the HV system NOT need to be depowered?
A) Removing the HV battery pack
B) Performing routine service
C) Replacing the HV cables
D) Replacing the HV air-conditioning compressor
Answer: B
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
7) What will occur if the safety interlock system detects an open circuit on a hybrid vehicle?
A) If the engine is running, it will detect a fault and set a DTC. It also opens the power relays,
turning off the "ready" light.
B) If the vehicle is moving, it will allow it to continue until a stop, and will disable the ICE.
C) If the vehicle is not moving, it will disable the ICE immediately.
D) All of the answers are correct.
Answer: A
Page Ref: 8
Objective: 1-6 Explain the purpose of the safety interlock system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
2
Copyright © 2023 Pearson Education, Inc.
,8) What precautions need to be taken to ensure the hybrid or electric vehicle work area is safe?
A) The area should be clean and dry.
B) The work area should be clearly marked.
C) No special precautions are needed.
D) The area should be clean and dry and clearly marked.
Answer: D
Page Ref: 3
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
9) What is the purpose of a megohmmeter or insulation tester?
A) Check for continuity between the HV cables and the vehicle chassis.
B) Measure the resistance of connections in the LV system.
C) Measure the current flow through the HV cables.
D) None of the answers is correct.
Answer: A
Page Ref: 7
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
10) What should be done if the HV rubber gloves inspection dates are found to be expired?
A) Use them anyway if they look OK.
B) Use them if they pass the air test.
C) Send the gloves to a qualified inspection laboratory.
D) Throw the gloves away.
Answer: C
Page Ref: 4
Objective: 1-5 Describe the process for testing rubber gloves before use.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
11) If the engine is not running, Technician A says that the high-voltage circuits are depowered.
Technician B says that all high voltage wiring is orange in color. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: B
Page Ref: 3
Objective: 1-3 Explain the difference between yellow/blue and orange high-voltage cables.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
3
Copyright © 2023 Pearson Education, Inc.
,12) How often should linesman's gloves be inspected by a qualified testing lab?
A) Every six months
B) Daily
C) Monthly
D) Yearly
Answer: A
Page Ref: 4
Objective: 1-5 Describe the process for testing rubber gloves before use.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
13) The high voltage cables ________.
A) are orange in color
B) are energized during events where the ignition switch is in the "on" position
C) Both A and B
D) Neither A nor B
Answer: C
Page Ref: 2-3
Objective: 1-3 Explain the difference between yellow/blue and orange high-voltage cables.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
14) What is true regarding protective gloves worn during HV system service?
A) Rubber gloves should be checked for leaks before each use
B) Leather gloves are worn over the rubber gloves to protect the rubber from damage
C) Both A and B
D) Neither A nor B
Answer: C
Page Ref: 5
Objective: 1-4 List the types of personal protective equipment.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
15) Technician A says that CAT I meter leads may be used to test HV system components as
long as the DMM itself is rated CAT III. Technician B says that CAT IV test leads are clamp-on
inductive type leads. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: B
Page Ref: 7
Objective: 1-2 Describe the differences between a CAT I, CAT II, CAT III, and CAT IV
multimeter.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
4
Copyright © 2023 Pearson Education, Inc.
,16) Technician A says that DMMs are assigned CAT ratings based on voltage capacity alone.
Technician B says that DMMs are rated according to their ability to handle potential electrical
energy. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: B
Page Ref: 7
Objective: 1-2 Describe the differences between a CAT I, CAT II, CAT III, and CAT IV
multimeter.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
17) Technician A says that a completely assembled electric motor is not likely to produce injury
by electrical shock. Technician B says that turning off the ignition on an HEV causes the system
main relay to disable the high voltage system. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: C
Page Ref: 3
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
18) Which statement regarding high voltage circuitry in HEVs is NOT correct?
A) The HV system is not energized when the ICE is in idle stop mode and the electrical A/C
compressor is running
B) The system is disabled when the ignition switch is off
C) The system is energized when the ICE is running and the vehicle is accelerating
D) None of these
Answer: A
Page Ref: 3
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
19) How long can power be retained in the high voltage system once it has been disabled?
A) 10 minutes
B) Less than 90 seconds
C) 9 hours
D) None of these
Answer: A
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
5
Copyright © 2023 Pearson Education, Inc.
,20) On a HEV that uses a "START" push button, what precaution should be taken when de-
powering the vehicle?
A) Make sure the key fob is at least 15 feet away from the vehicle
B) Make sure the key is somewhere inside the vehicle
C) Put the key fob in the trunk
D) No special precautions are needed
Answer: A
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
21) What is the recommended location to store a HEV ignition key during service?
A) Top of the technician's tool box
B) Lock box
C) In the vehicle glove box
D) Leave the key in the ignition
Answer: B
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
22) Which of these is NOT a step in de-powering the high voltage system?
A) Remove the ignition key
B) Disconnect the 12 volt battery
C) Remove the ground interlock fuse
D) Remove the high voltage service plug
Answer: C
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
23) Which of these is NOT a recommended PPE?
A) Cotton clothing
B) Insulated rubber mat
C) Plastic tool box
D) Insulated shoes
Answer: C
Page Ref: 5
Objective: 1-4 List the types of personal protective equipment.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
6
Copyright © 2023 Pearson Education, Inc.
,Electric and Hybrid Electric Vehicles, 1e (Halderman)
Chapter 2 Introduction to Hybrid Vehicles
1) What is the difference between a mild hybrid and a full hybrid?
A) A mild hybrid will propel the vehicle in electric mode.
B) A full hybrid will propel the vehicle in electric mode.
C) There are no differences between mild and full hybrid vehicles.
D) None of the answers are correct.
Answer: B
Page Ref: 20
Objective: 2-3 Explain the differences in the levels of hybrid vehicles.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
2) What is the difference between a hybrid electric vehicle (HEV) and a plug-in electric vehicle
(PHEV)?
A) Both an HEV and PHEV have to be plugged in.
B) Only the PHEV needs to be plugged in to achieve maximum range.
C) A PHEV does not use an ICE.
D) An HEV uses a high-voltage battery that has a higher capacity than a PHEV.
Answer: B
Page Ref: 15
Objective: 2-1 Explain the definition of a hybrid and electric vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
3) One-pedal driving means ________.
A) the vehicle only has one pedal
B) the vehicle has the ability to slow and often stop using just the accelerator pedal
C) the vehicle does not use regenerative brakes but just friction brakes
D) the vehicle uses the accelerator pedal to accelerate and the parking brake level to slow and
stop
Answer: B
Page Ref: 18
Objective: 2-2 Describe the unique characteristics of owning or driving a hybrid or electric
vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
4) An electric vehicle is also called a ________.
A) self-driving vehicle
B) battery electric vehicle (BEV)
C) hybrid electric vehicle (HEV)
D) plug-in hybrid electric vehicle (PHEV)
Answer: B
Page Ref: 15
Objective: 2-1 Explain the definition of a hybrid and electric vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
1
Copyright © 2023 Pearson Education, Inc.
, 5) Most hybrid and electric vehicles have a different maintenance schedule than a conventional
vehicle. What is not commonly performed on an EV?
A) Tire rotation
B) Coolant Flush
C) Cabin filter replacement
D) Windshield washer fluid
Answer: B
Page Ref: 18
Objective: 2-2 Describe the unique characteristics of owning or driving a hybrid or electric
vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
6) Range anxiety is ________.
A) the fear of running out of electrical battery charge and being left stranded
B) the fear of having to recharge on the way to work if the distance is greater than 5 miles
C) normal anxiety when first owning an EV
D) Both A and C
Answer: D
Page Ref: 18
Objective: 2-2 Describe the unique characteristics of owning or driving a hybrid or electric
vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
7) What is the typical battery configuration in a micro hybrid?
A) A 12-volt battery and a 144-volt battery
B) Two 12-volt batteries
C) A 12-volt battery and a 42-volt battery
D) A 12-volt battery and a 300-volt battery
Answer: B
Page Ref: 20
Objective: 2-3 Explain the differences in the levels of hybrid vehicles.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
8) A medium hybrid uses ________.
A) A 12-volt battery and a 144-volt battery
B) Two 12-volt batteries
C) A 12-volt battery and a 42-volt battery
D) A 12-volt battery and a 300-volt battery
Answer: C
Page Ref: 20
Objective: 2-3 Explain the differences in the levels of hybrid vehicles.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
2
Copyright © 2023 Pearson Education, Inc.
Vehicles, 1st edition James Halderman
Notes
1- The file is chapter after chapter.
2- We have shown you few pages sample.
3- The file contains all Appendix and Excel sheet
if it exists.
4- We have all what you need, we make update
at every time. There are many new editions
waiting you.
5- If you think you purchased the wrong file You
can contact us at every time, we can replace it
with true one.
Our email:
,Electric and Hybrid Electric Vehicles, 1e (Halderman)
Chapter 1 Hybrid and Electric Vehicle Safety
1) Rubber gloves should be worn whenever working on or near the high-voltage circuits or
components of a hybrid electric vehicle. Technician says A that the rubber gloves should be rated
at 1000 volts or higher. Technician B says that leather gloves should be worn over the high-
voltage rubber gloves. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: C
Page Ref: 4
Objective: 1-4 List the types of personal protective equipment.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
2) A CAT III certified DMM should be used whenever measuring high-voltage circuits or
components. The
CAT III rating relates to ________.
A) high voltage
B) high energy
C) high electrical resistance
D) both high energy and high voltage
Answer: D
Page Ref: 7
Objective: 1-2 Describe the differences between a CAT I, CAT II, CAT III, and CAT IV
multimeter.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
3) All of the following will shut off the high voltage to components and circuits EXCEPT
________.
A) opening the driver's door
B) turning the ignition off
C) disconnecting the 12-volt auxiliary battery
D) removing the main fuse, relay, or HV plug
Answer: A
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
1
Copyright © 2023 Pearson Education, Inc.
,4) What can occur if a hybrid electric vehicle is pushed in the shop?
A) The HV battery pack can be damaged.
B) The tires will be locked unless the ignition is on.
C) Damage to the electronic controller can occur.
D) High voltage will be generated by the motor/generator as the wheels turn.
Answer: D
Page Ref: 10
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
5) When hoisting a hybrid or electric vehicle, what precautions must the technician follow to
ensure personal safety and avoid damage to the vehicle?
A) Make sure the lift points do not contact HV cables.
B) Do not lift the vehicle by the battery case.
C) Ensure the lift points are clear of battery cooling and refrigeration lines.
D) All of the answers are correct.
Answer: D
Page Ref: 9
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
6) When does the HV system NOT need to be depowered?
A) Removing the HV battery pack
B) Performing routine service
C) Replacing the HV cables
D) Replacing the HV air-conditioning compressor
Answer: B
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
7) What will occur if the safety interlock system detects an open circuit on a hybrid vehicle?
A) If the engine is running, it will detect a fault and set a DTC. It also opens the power relays,
turning off the "ready" light.
B) If the vehicle is moving, it will allow it to continue until a stop, and will disable the ICE.
C) If the vehicle is not moving, it will disable the ICE immediately.
D) All of the answers are correct.
Answer: A
Page Ref: 8
Objective: 1-6 Explain the purpose of the safety interlock system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
2
Copyright © 2023 Pearson Education, Inc.
,8) What precautions need to be taken to ensure the hybrid or electric vehicle work area is safe?
A) The area should be clean and dry.
B) The work area should be clearly marked.
C) No special precautions are needed.
D) The area should be clean and dry and clearly marked.
Answer: D
Page Ref: 3
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
9) What is the purpose of a megohmmeter or insulation tester?
A) Check for continuity between the HV cables and the vehicle chassis.
B) Measure the resistance of connections in the LV system.
C) Measure the current flow through the HV cables.
D) None of the answers is correct.
Answer: A
Page Ref: 7
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
10) What should be done if the HV rubber gloves inspection dates are found to be expired?
A) Use them anyway if they look OK.
B) Use them if they pass the air test.
C) Send the gloves to a qualified inspection laboratory.
D) Throw the gloves away.
Answer: C
Page Ref: 4
Objective: 1-5 Describe the process for testing rubber gloves before use.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
11) If the engine is not running, Technician A says that the high-voltage circuits are depowered.
Technician B says that all high voltage wiring is orange in color. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: B
Page Ref: 3
Objective: 1-3 Explain the difference between yellow/blue and orange high-voltage cables.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
3
Copyright © 2023 Pearson Education, Inc.
,12) How often should linesman's gloves be inspected by a qualified testing lab?
A) Every six months
B) Daily
C) Monthly
D) Yearly
Answer: A
Page Ref: 4
Objective: 1-5 Describe the process for testing rubber gloves before use.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
13) The high voltage cables ________.
A) are orange in color
B) are energized during events where the ignition switch is in the "on" position
C) Both A and B
D) Neither A nor B
Answer: C
Page Ref: 2-3
Objective: 1-3 Explain the difference between yellow/blue and orange high-voltage cables.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
14) What is true regarding protective gloves worn during HV system service?
A) Rubber gloves should be checked for leaks before each use
B) Leather gloves are worn over the rubber gloves to protect the rubber from damage
C) Both A and B
D) Neither A nor B
Answer: C
Page Ref: 5
Objective: 1-4 List the types of personal protective equipment.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
15) Technician A says that CAT I meter leads may be used to test HV system components as
long as the DMM itself is rated CAT III. Technician B says that CAT IV test leads are clamp-on
inductive type leads. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: B
Page Ref: 7
Objective: 1-2 Describe the differences between a CAT I, CAT II, CAT III, and CAT IV
multimeter.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
4
Copyright © 2023 Pearson Education, Inc.
,16) Technician A says that DMMs are assigned CAT ratings based on voltage capacity alone.
Technician B says that DMMs are rated according to their ability to handle potential electrical
energy. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: B
Page Ref: 7
Objective: 1-2 Describe the differences between a CAT I, CAT II, CAT III, and CAT IV
multimeter.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
17) Technician A says that a completely assembled electric motor is not likely to produce injury
by electrical shock. Technician B says that turning off the ignition on an HEV causes the system
main relay to disable the high voltage system. Which technician is correct?
A) Technician A only
B) Technician B only
C) Both technicians A and B
D) Neither technician A nor B
Answer: C
Page Ref: 3
Objective: 1-1 Explain the need for caution around the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
18) Which statement regarding high voltage circuitry in HEVs is NOT correct?
A) The HV system is not energized when the ICE is in idle stop mode and the electrical A/C
compressor is running
B) The system is disabled when the ignition switch is off
C) The system is energized when the ICE is running and the vehicle is accelerating
D) None of these
Answer: A
Page Ref: 3
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
19) How long can power be retained in the high voltage system once it has been disabled?
A) 10 minutes
B) Less than 90 seconds
C) 9 hours
D) None of these
Answer: A
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
5
Copyright © 2023 Pearson Education, Inc.
,20) On a HEV that uses a "START" push button, what precaution should be taken when de-
powering the vehicle?
A) Make sure the key fob is at least 15 feet away from the vehicle
B) Make sure the key is somewhere inside the vehicle
C) Put the key fob in the trunk
D) No special precautions are needed
Answer: A
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
21) What is the recommended location to store a HEV ignition key during service?
A) Top of the technician's tool box
B) Lock box
C) In the vehicle glove box
D) Leave the key in the ignition
Answer: B
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
22) Which of these is NOT a step in de-powering the high voltage system?
A) Remove the ignition key
B) Disconnect the 12 volt battery
C) Remove the ground interlock fuse
D) Remove the high voltage service plug
Answer: C
Page Ref: 9
Objective: 1-7 Describe the process for depowering the high-voltage system.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
23) Which of these is NOT a recommended PPE?
A) Cotton clothing
B) Insulated rubber mat
C) Plastic tool box
D) Insulated shoes
Answer: C
Page Ref: 5
Objective: 1-4 List the types of personal protective equipment.
ASE: L3D Prepare for ASE L3 certification test section "D" (Power Electronics).
6
Copyright © 2023 Pearson Education, Inc.
,Electric and Hybrid Electric Vehicles, 1e (Halderman)
Chapter 2 Introduction to Hybrid Vehicles
1) What is the difference between a mild hybrid and a full hybrid?
A) A mild hybrid will propel the vehicle in electric mode.
B) A full hybrid will propel the vehicle in electric mode.
C) There are no differences between mild and full hybrid vehicles.
D) None of the answers are correct.
Answer: B
Page Ref: 20
Objective: 2-3 Explain the differences in the levels of hybrid vehicles.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
2) What is the difference between a hybrid electric vehicle (HEV) and a plug-in electric vehicle
(PHEV)?
A) Both an HEV and PHEV have to be plugged in.
B) Only the PHEV needs to be plugged in to achieve maximum range.
C) A PHEV does not use an ICE.
D) An HEV uses a high-voltage battery that has a higher capacity than a PHEV.
Answer: B
Page Ref: 15
Objective: 2-1 Explain the definition of a hybrid and electric vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
3) One-pedal driving means ________.
A) the vehicle only has one pedal
B) the vehicle has the ability to slow and often stop using just the accelerator pedal
C) the vehicle does not use regenerative brakes but just friction brakes
D) the vehicle uses the accelerator pedal to accelerate and the parking brake level to slow and
stop
Answer: B
Page Ref: 18
Objective: 2-2 Describe the unique characteristics of owning or driving a hybrid or electric
vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
4) An electric vehicle is also called a ________.
A) self-driving vehicle
B) battery electric vehicle (BEV)
C) hybrid electric vehicle (HEV)
D) plug-in hybrid electric vehicle (PHEV)
Answer: B
Page Ref: 15
Objective: 2-1 Explain the definition of a hybrid and electric vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
1
Copyright © 2023 Pearson Education, Inc.
, 5) Most hybrid and electric vehicles have a different maintenance schedule than a conventional
vehicle. What is not commonly performed on an EV?
A) Tire rotation
B) Coolant Flush
C) Cabin filter replacement
D) Windshield washer fluid
Answer: B
Page Ref: 18
Objective: 2-2 Describe the unique characteristics of owning or driving a hybrid or electric
vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
6) Range anxiety is ________.
A) the fear of running out of electrical battery charge and being left stranded
B) the fear of having to recharge on the way to work if the distance is greater than 5 miles
C) normal anxiety when first owning an EV
D) Both A and C
Answer: D
Page Ref: 18
Objective: 2-2 Describe the unique characteristics of owning or driving a hybrid or electric
vehicle.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
7) What is the typical battery configuration in a micro hybrid?
A) A 12-volt battery and a 144-volt battery
B) Two 12-volt batteries
C) A 12-volt battery and a 42-volt battery
D) A 12-volt battery and a 300-volt battery
Answer: B
Page Ref: 20
Objective: 2-3 Explain the differences in the levels of hybrid vehicles.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
8) A medium hybrid uses ________.
A) A 12-volt battery and a 144-volt battery
B) Two 12-volt batteries
C) A 12-volt battery and a 42-volt battery
D) A 12-volt battery and a 300-volt battery
Answer: C
Page Ref: 20
Objective: 2-3 Explain the differences in the levels of hybrid vehicles.
ASE: L3E Prepare for ASE L3 certification test section "E" (Hybrid Supporting Systems).
2
Copyright © 2023 Pearson Education, Inc.
